Common Specifications & Procedures
ECOSPORT COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Specifications | ||
| Torque | |||
| 1.0L ECOBOOST (92KW/125PS) | Refer to the appropriate component in Removal And Installation | ||
| 2.0L DURATEC-HE (129KW/175PS) | Refer to the appropriate component in Removal And Installation | ||
| Hub Nut | 188 lb.ft (255 Nm) | ||
| Battery | Specifications | ||
| Brakes | |||
| Bleeding Sequence | Brake System Pressure Bleeding | ||
| Front Disc Brakes w/Torque | Torque Specifications | ||
| Rear Disc Brakes w/Torque | Torque Specifications | ||
| Charging | |||
| Generator w/Torque | |||
| 1.0L ECOBOOST (92KW/125PS) | 18 lb.ft (25 Nm) | ||
| 2.0L DURATEC-HE (129KW/175PS) | Generator Bolts: 18 lb.ft (25 Nm) Upper Generator Mounting Bolt: 18 lb.ft (25 Nm) |
||
| Drive Belts | |||
| Adjustment | |||
| 1.0L ECOBOOST (92KW/125PS) | Accessory Drive | ||
| 2.0L DURATEC-HE (129KW/175PS) | Accessory Drive | ||
| Belt Routing | |||
| 1.0L ECOBOOST (92KW/125PS) | Accessory Drive - Component Location | ||
| 2.0L DURATEC-HE (129KW/175PS) | Accessory Drive - Component Location | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 1.0L ECOBOOST (92KW/125PS) | Specifications | ||
| 2.0L DURATEC-HE (129KW/175PS) | Specifications | ||
| Pressure Relief Cap | |||
| 1.0L ECOBOOST (92KW/125PS) | 130 to 150 kPa (18 to 21 psi) | ||
| 2.0L DURATEC-HE (129KW/175PS) | 130 to 150 kPa (18 to 21 psi) | ||
| Thermostat R & I | |||
| 1.0L ECOBOOST (92KW/125PS) | Thermostat Housing | ||
| 2.0L DURATEC-HE (129KW/175PS) | Thermostat Housing | ||
| Water Pump R & I | |||
| 1.0L ECOBOOST (92KW/125PS) | Coolant Pump | ||
| 2.0L DURATEC-HE (129KW/175PS) | Coolant Pump | ||
| Engine Mechanical | |||
| 1.0L ECOBOOST (92KW/125PS) | |||
| Compression | Specifications | ||
| Oil pressure (hot @ 800 rpm) | 14.5 psi (100 kPa) | ||
| Oil pressure (hot @ 2, 000 rpm) | 29.0 psi (200 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to the appropriate component in Removal And Installation | ||
| 2.0L DURATEC-HE (129KW/175PS) | |||
| Compression | Specifications | ||
| Oil pressure (hot @ 2, 000 rpm) | 29.0 -38.9 psi (200 -268 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to the appropriate component in Removal And Installation | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | |||
| 1.0L ECOBOOST (92KW/125PS) | Flexplate 37 lb.ft (50 Nm) |
||
| 2.0L DURATEC-HE (129KW/175PS) |
Stage 1: Tighten to 50 Nm (37 lb-ft) Stage 2: Tighten to 80 Nm (59 lb-ft) Stage 3: Tighten to 112 Nm (83 lb-ft) |
||
| Fuel System | |||
| Fuel Filter Location | Vehicle has a lifetime fuel filter which is serviced as part of the Fuel Pump (FP) module. | ||
| Fuel Filter R & I | |||
| 1.0L ECOBOOST (92KW/125PS) | Fuel Pump And Sender Unit | ||
| 2.0L DURATEC-HE (129KW/175PS) | Fuel Pump And Sender Unit \ | ||
| Pressure Release Procedure | |||
| 1.0L ECOBOOST (92KW/125PS) | Fuel System Pressure Release | ||
| 2.0L DURATEC-HE (129KW/175PS) | Fuel System Pressure Release | ||
| Pressure Specification | |||
| 1.0L ECOBOOST (92KW/125PS) | Specifications | ||
| 2.0L DURATEC-HE (129KW/175PS) | Specifications | ||
| Fuel Pressure Test Procedure | |||
| 1.0L ECOBOOST (92KW/125PS) | Fuel System Pressure Check | ||
| 2.0L DURATEC-HE (129KW/175PS) | Fuel System Pressure Check | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires | Engine has coil-on-plug ignition. | ||
| Spark Plugs | |||
| 1.0L ECOBOOST (92KW/125PS) | |||
| Type | HYFS 093 YEC | ||
| Gap | 0.7 mm | ||
| Torque | 133 lb.in (15 Nm) | ||
| 2.0L DURATEC-HE (129KW/175PS) | |||
| Type | CYFS-12 Y1 | ||
| Gap | 0.035 in (.9 mm) | ||
| Torque | 133 lb.in (15 Nm) | ||
| Starting | |||
| Starter w/Torque | |||
| 1.0L ECOBOOST (92KW/125PS) | Starter Motors Nuts: 18 lb.ft (25 Nm) | ||
| 2.0L DURATEC-HE (129KW/175PS) | 26 lb.ft (35 Nm) | ||
| Wheel Alignment | |||
| Adjustment Specifications | Specifications | ||
| Torque | Refer to the appropriate component in General Procedures | ||
| Wheel & Tire | |||
| Wheel Nuts | 98 lb.ft (133 Nm) | ||