LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2017 >> Fusion Titanium, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Handles, Locks, Latches And Entry Systems (Except Hybrid) >> Diagnosis And Testing >> Locks, Latches and Entry Systems >> Pinpoint Tests >> Pinpoint Test X : The Remote Start Feature Is Inoperative >> Pinpoint Test X : The Remote Start Feature Is Inoperative

Pinpoint Test X : The Remote Start Feature Is Inoperative

NOTE: This pinpoint test does not diagnose dealer installed remote start systems.

  1. X1 CHECK THE REMOTE START FEATURE ENABLE/DISABLE SETTING

    • Ignition ON.

    • Using the steering wheel control switch, check remote start feature setting in the message center.

    Is the remote start feature enabled? 

    Yes  GO to  X2
    No  ENABLE the remote start feature.

  2. X2 CHECK THE PARK DETECT SWITCH INPUT

    • Ignition ON.

    • Verify the PRNDL displays correctly in the IPC. When the vehicle is in PARK, the P should be highlighted or displayed prominently.

    Does the PRNDL display correctly? 

    Yes  GO to  X3
    No  DIAGNOSE the PRNDL. Refer to: Instrumentation, Message Center and Warning Chimes .

  3. X3 CHECK FOR BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, carry out the BCM self-test.

    Are any BCM Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to BCM DTC Chart .
    No  GO to  X4

  4. X4 CHECK FOR POWERTRAIN DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, carry out the PCM/ SOBDMC KOEO and KOER self-tests.

    Are any PCM/ SOBDMC Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to the PCM DTC Chart in the appropriate Electronic Engine Controls article or Refer to Engine Controls - Introduction (Except Diesel & Hybrid) .
    No  GO to  X5

  5. X5 CHECK THE RKE (REMOTE KEYLESS ENTRY) FUNCTIONALITY

    • Ignition OFF.

    • Using the RKE function of the key, press the luggage compartment lid release button twice, the lock button and then the unlock button.

    Do all the functions tested of the RKE transmitter operate (lock, unlock and luggage compartment lid release)? 

    Yes  GO to  X6
    No  If all of the functions are inoperative, GO to Pinpoint Test U  If an individual function is inoperative, GO to Pinpoint Test V 

  6. X6 CHECK THE WAKE-UP CIRCUIT FOR VOLTAGE AT THE PCM (POWERTRAIN CONTROL MODULE) USING THE BCM (BODY CONTROL MODULE) PID (PARAMETER IDENTIFICATION) (PCM) WAKE-UP OUTPUT CONTROL (PCM_WKUP_CTRL)

    • Disconnect PCM B connector.

    • Ignition ON.

    • Using a diagnostic scan tool, command the BCM PID PCM_WKUP_CTRL on.

    • Measure:

      1.5L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1915B-28
      GFD196534Courtesy of FORD MOTOR COMPANY
      		 Ground

      2.0L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1381B-28
      GFD196534Courtesy of FORD MOTOR COMPANY
      		 Ground

      2.5L TIVCT 

      Positive Lead Measurement / Action Negative Lead
      C1551B-21
      GFD196534Courtesy of FORD MOTOR COMPANY
      		 Ground

      2.7L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1231B-28
      GFD196534Courtesy of FORD MOTOR COMPANY
      		 Ground

      2.0L Hybrid 

      Positive Lead Measurement / Action Negative Lead
      C175B-21
      GFD196534Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the voltage greater than 11 volts? 

    Yes  GO to  X8
    No  GO to  X7

  7. X7 CHECK THE WAKE-UP CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Measure:

      1.5L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1915B-28
      GFD196532Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

      2.0L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1381B-28
      GFD196532Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

      2.5L TIVCT 

      Positive Lead Measurement / Action Negative Lead
      C1551B-21
      GFD196532Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

      2.7L GTDI 

      Positive Lead Measurement / Action Negative Lead
      C1231B-28
      GFD196532Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

      2.0L Hybrid 

      Positive Lead Measurement / Action Negative Lead
      C175B-21
      GFD196532Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

    Is the resistance less than 3 ohms? 

    Yes  GO to  X9
    No  REPAIR the circuit.

  8. X8 VERIFY THE REMOTE START FUNCTION IS INOPERATIVE

    • Ignition OFF.

    • Connect PCM B connector.

    • Close all the doors, the hood and the luggage compartment lid.

    • NOTE: Each button press must be done within three seconds of each other.

      Using the key:

      • Press the door lock button.
      • Press the remote start button twice.

    Does the vehicle remotely start? 

    Yes  The system is operating correctly. INFORM the customer of the correct vehicle remote start operation.
    No  REPLACE the suspect key. PROGRAM the new key. REFER to: Anti-Theft Key Programming - Scan Tool .

  9. X9 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

    • Disconnect and inspect all the BCM connectors.

    • Repair:

      • corrosion (install new connectors or terminals - clean module pins)
      • damaged or bent pins - install new terminals pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the BCM connectors and make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to BCM Hardware Testing -- Fusion (Except Hybrid) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals