Common Specifications & Procedures
POLICE INTERCEPTOR UTILITY COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| EMTC System | SPECIFICATIONS | ||
| DATC System | SPECIFICATIONS | ||
| Torque | |||
| EMTC System | TORQUE SPECIFICATIONS | ||
| DATC System | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 350 N.m (258 Ft. Lbs.) | ||
| Rear | 350 N.m (258 Ft. Lbs.) | ||
| Battery | SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Front Disc Brakes w/Torque | SPECIFICATIONS | ||
| Rear Disk Brakes w/Torque | SPECIFICATIONS | ||
| Charging | |||
| Generator w/Torque | |||
| 3.5L GTDI | GENERATOR -- 3.5L GTDI | ||
| 3.7L Ti-VCT | Generator Bolt: 47 Nm (35 lb-ft) Generator Stud Nut: 47 Nm (35 lb-ft) Generator Stud: 47 Nm (35 lb-ft) |
||
| Drive Belts | |||
| Adjustment | SPECIFICATIONS | ||
| Belt Routing | |||
| 3.5L GTDI | COMPONENT LOCATION | ||
| 3.7L Ti-VCT | COMPONENT LOCATION | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | 13.8 -18.1 psi (95-125 kPa) | ||
| Thermostat R & I | |||
| 3.5L GTDI | THERMOSTAT -- 3.5L GTDI | ||
| 3.7L Ti-VCT | THERMOSTAT -- 3.7L TI-VCT | ||
| Water Pump R & I | |||
| 3.5L GTDI | COOLANT PUMP -- 3.5L GTDI | ||
| 3.7L Ti-VCT | COOLANT PUMP -- 3.7L TI-VCT | ||
| Engine Mechanical | |||
| 3.5L GTDI | |||
| Compression | SPECIFICATIONS | ||
| Oil Pressure @ 1, 500 RPM (engine at normal operating temperature) | Minimum 30 psi | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.7L Ti-VCT | |||
| Compression | SPECIFICATIONS | ||
| Oil Pressure @1, 500 RPM (engine at normal operating temperature) | Minimum 30 psi | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | |||
| 3.5L Ti-VCT | For tightening sequence, refer to FLEXPLATE
procedure. 80 Nm (59 lb-ft) |
||
| 3.7L Ti-VCT | For tightening sequence, refer to FLEXPLATE
procedure. 80 Nm (59 lb-ft) |
||
| Fuel System | |||
| Fuel Filter Location | Vehicle has a lifetime fuel filter which is serviced as part of the Fuel Pump (FP) module. | ||
| Fuel Filter R & I | FUEL PUMP ASSEMBLY | ||
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Pressure Specification | SPECIFICATIONS | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires | Engine has coil-on-plug ignition. | ||
| Spark Plugs | |||
| 3.5L GTDI | |||
| Type | Motorcraft CYFS 12 YT3 | ||
| Gap | 0.889 mm (0.035 in) | ||
| Torque | 133 In. Lbs. (15 N.m) | ||
| 3.7L Ti-VCT | |||
| Type | Motorcraft CYFS-12F-5 | ||
| Gap | 1.25 mm (0.049 in) - 1.35 mm (0.0531 in) | ||
| Torque | 133 In. Lbs. (15 N.m) | ||
| Starting | |||
| Starter w/Torque | STARTER MOTOR -- 3.5L GTDI or STARTER MOTOR -- 3.7L TI-VCT | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque | ALIGNMENT SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque (All Except Police Vehicles) | 100 Ft. Lbs. (135 N.m) | ||
| Wheel Lug Nut Torque (Police Vehicles) | 110 Ft. Lbs. (149 N.m) | ||