LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2015 >> Flex SEL, AWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine - 3.5L Ti-VCT >> Specifications >> Specifications >> Torque Specifications

Torque Specifications

Description Nm lb-ft lb-in
A/C compressor bolts and nut 25 18 -
A/C compressor stud 9 - 80
A/C tube nuts 15 - 133
Accessory drive belt tensioner bolts 11 - 97
Battery cable power feed cable nut 5 - 44
Bellhousing -to-engine bolts 48 35 -
Block coolant drain plug - RH (1) - - -
Block coolant drain plug - LH (2) - - -
Block heater 40 30 -
Block oil gallery plug - LH (3) 48 35 -
Block oil gallery plug - rear (3) 85 63 -
Block oil gallery plug - RH (3) 32 24 -
Camshaft bearing cap bolts (4) - - -
Camshaft Position (CMP) sensor bolts 10 - 89
Connecting rod cap bolts (4) - - -
Coolant pump bolts (4) - - -
Crankshaft rear seal retainer plate bolts (4) - - -
Crankshaft Position (CKP) sensor bolt 10 - 89
CKP sensor heat shield nuts 10 - 89
Crankshaft pulley bolt (4) - - -
Cylinder head bolts (4) - - -
Cylinder Head Temperature (CHT) sensor 10 - 89
Engine front cover bolts (4) - - -
Engine front cover ground wire bolt 10 - 89
Engine ground wire-to-shock tower bolt 10 - 89
Engine lifting eye bolts 24 18 -
Engine mount brace bolt and nut 20 - 177
Engine mount bracket bolts 30 22 -
Engine mount-to-engine nuts 63 46 -
Engine mount-to-frame bolts 90 66 -
Engine oil filter (5) - - -
Engine Oil Pressure (EOP) switch (4) - - -
Engine-to-bellhousing bolts 48 35 -
Exhaust manifold/catalytic converter manifold bracket nuts - LH 30 22 -
Exhaust manifold/catalytic converter manifold heat shield bolts 10 - 89
Exhaust manifold/catalytic converter manifold nuts (4) - - -
Exhaust manifold/catalytic converter manifold studs 12 - 106
Flexplate bolts (4) - - -
Fuel supply tube-to-engine front cover bolt 10 - 89
Generator bolt and nut 47 35 -
Generator B+ terminal nut 17 - 150
Generator stud 8 - 71
Ground wire-to-body retainer 10 - 89
Ground wire-to-engine bolt 10 - 89
Ground wire-to-RH cylinder head bolt 10 - 89
Ignition coil-on-plug bolts 7 - 62
Knock Sensor (KS) bolts 20 - 177
Lower intake manifold bolts (4) - - -
Main bearing bolts (4) - - -
Main bearing cap support brace bolts (4) - - -
Oil cooler bolts (4) - - -
Oil filter adapter (4) - - -
Oil pan bolts (4) - - -
Oil pan drain plug 27 20 -
Oil pan-to-transaxle bolts 48 35 -
Oil pump bolts 10 - 89
Oil pump screen and pickup tube bolts 10 - 89
Piston oil cool valves 4 - 35
Power Transfer Unit (PTU) 90 66 -
PTU support bracket bolts 70 52 -
Rear driveshaft-to-PTU flange bolts 70 52 -
Spark plugs 15 - 133
Starter bolt and stud bolt 27 20 -
Starter B+ terminal nut 12 - 106
Starter S-terminal nut 5 - 44
Thermostat housing bolts 10 - 89
Timing chain guide bolts 10 - 89
Timing chain tensioner bolts 10 - 89
Torque converter-to-flexplate bolts 55 41 -
Transaxle mount bracket bolt 80 59 -
Transaxle mount bracket nuts 63 46 -
Transaxle mount through bolt and nut 175 129 -
Transaxle-to-engine bolts 48 35 -
Upper intake manifold bolts (4) - - -
Upper intake manifold support bracket-to-engine bolt 10 - 89
Upper intake manifold-to-support bracket bolt 10 - 89
Valve cover bolts and stud bolts (4) - - -
VCT bolts (4) - - -
VCT oil control solenoid bolts (4) - - -

() Tighten to 10 Nm (89 lb-in) plus an additional 720 degrees.

() Tighten to 16 Nm (142 lb-in) plus an additional 180 degrees.

() Discard original plug and O-ring seal. Install a new plug and O-ring seal to specified torque, no sealer or lubricant required.

() Refer to the procedure in this article.

() Tighten to 5 Nm (44 lb-in) plus an additional 180 degrees.