Driver Door Module (DDM) DTC Table
DDM DTC DESCRIPTION
| DTC | Description | Action |
|---|---|---|
| B1087:83 | LIN Bus "A": Value Of Signal Protection Calculation Incorrect | GO to PINPOINT TEST U |
| B1087:86 | LIN Bus "A": Signal Invalid | GO to PINPOINT TEST U |
| B1087:88 | LIN Bus "A": Bus Off | GO to PINPOINT TEST U |
| B1108:11 | Driver Door Central Locking Motor: Circuit Short To Ground | GO to PINPOINT TEST I |
| B1108:15 | Driver Door Central Locking Motor: Circuit Short To Battery Or Open | GO to PINPOINT TEST I |
| B110A:01 | Rear Door Driver Side Central Locking Motor: General Electrical Failure | GO to PINPOINT TEST I |
| B1288:02 | Rear Lock Motor Common Circuit: General Signal Failure | GO to PINPOINT TEST I |
| B12AB:11 | Front Window Position Sensor Power Supply: Circuit Short To Ground | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12B6:11 | Front Lock Motor Common Circuit: Circuit Short To Ground | GO to PINPOINT TEST I |
| B12B6:15 | Front Lock Motor Common Circuit: Circuit Short To Battery Or Open | GO to PINPOINT TEST I |
| B12C2:11 | Puddle Lamp: Circuit Short To Ground | REFER to: INTERIOR LIGHTING . |
| B12C2:15 | Puddle Lamp: Circuit Short To Battery Or Open | REFER to: INTERIOR LIGHTING . |
| B12C3:11 | Rear Window Position Sensor Power Supply: Circuit Short To Ground | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C4:11 | Mirror Turn Indicator: Circuit Short To Ground | REFER to: TURN SIGNAL AND HAZARD LAMPS . |
| B12C4:15 | Mirror Turn Indicator: Circuit Short To Battery Or Open | REFER to: TURN SIGNAL AND HAZARD LAMPS . |
| B12C5:02 | Front Window Lifter Motor Up Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C6:02 | Rear Window Lifter Motor Up Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C7:02 | Rear Window Lifter Motor Down Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C8:02 | Front Window Lifter Motor Down Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B12D8:15 | Mirror Heater Output: Circuit Short To Battery Or Open | REFER to: REAR VIEW MIRRORS . |
| B12DC:02 | Front Window Motion/Position Sensor: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DC:54 | Front Window Motion/Position Sensor: Missing Calibration | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DD:02 | Rear Window Motion/Position Sensor: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DD:54 | Rear Window Motion/Position Sensor: Missing Calibration | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12E9:02 | Rear Window Local Up/Down Switch: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12FF:11 | Rear Door Switch Illumination: Circuit Short To Ground | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| B12FF:15 | Rear Door Switch Illumination: Circuit Short To Battery Or Open | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| B1302:11 | Mirror Motor Common: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B1C09:11 | Driver Left/Right Mirror Motor: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B1C10:11 | Driver Up/Down Mirror Motor: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| U0010:88 | Medium Speed Can Communication Bus: Bus Off | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC . VERIFY the integrity of the connectors and wiring. Refer to OEM WIRING DIAGRAMS -- EXCEPT ELECTRIC for schematic and connector information. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST V |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST W |
| U0201:87 | Lost Communication With "Door Control Module C": Missing Message | GO to PINPOINT TEST Y |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new DDM . REFER to: DOOR MODULE . |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM . REFER to: POWERTRAIN CONTROL MODULE (PCM) . |
| U0402:00 | Invalid Data Received From TCM: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM . REFER to: TRANSMISSION CONTROL MODULE (TCM) . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM . REFER to: BODY CONTROL MODULE (BCM) . |
| U2013:01 | Switch Pack: General Electrical Failure | REFER to: GLASS, FRAMES AND MECHANISMS - OVERVIEW . |
| U2013:87 | Switch Pack: Missing Message | REFER to: GLASS, FRAMES AND MECHANISMS - OVERVIEW . |
| U2014:44 | Control Module Hardware: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new DDM . REFER to: DOOR MODULE . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new DDM . REFER to: DOOR MODULE . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new DDM . REFER to: DOOR MODULE . |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to PINPOINT TEST AA |