Side Obstacle Detection Control Module - Left (Sod-L) And Side Obstacle Detection Control Module - Right (Sod-R)

DTC INDEX

DTC	Description	Action
B12DA:68	Blind Spot Warning Indicator: Event Information	REFER to the SYMPTOM CHART .
U0010:00	Medium Speed CAN Communication Bus: No Sub Type Information	Diagnose all related BCM Diagnostic Trouble Codes (DTCs) (U0037:88, U0040:00, U0041:00, U0043:00, U0044:00 or U0045:00) first. The SODL or SODR could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC ). CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the network test with a diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0121:87	Lost Communication with ABS Module: Missing Message	DISREGARD this DTC . DIAGNOSE any other symptom or Diagnostic Trouble Codes (DTCs) present in other modules. REFER to the appropriate DTC Chart.
U0140:00	Lost Communication with Body Control Module: No Sub Type Information	DIAGNOSE all related BCM Diagnostic Trouble Codes (DTCs) (U0037:88, U0040:00, U0041:00, U0043:00, U0044:00 or U0045:00) first. The SODL or SODR could not communicate with the BCM at a point in time. The fault is not currently present (the module had to communicate with the BCM to report this DTC to the scan tool). CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0155:01	Lost Communication With Instrument Panel Cluster (IPC) Control Module: General Electrical Failure	Go to PINPOINT TEST K
U0232:00	Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information	DIAGNOSE the SODL Does Not Respond To The Diagnostic Scan Tool. Refer to: COMMUNICATIONS NETWORK .
U0233:00	Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information	DIAGNOSE the SODR Does Not Respond To The Diagnostic Scan Tool. Refer to: COMMUNICATIONS NETWORK .
U0300:00	Internal Control Module Software Compatibility: No Sub Type Information	CLEAR the Diagnostic Trouble Codes (DTCs). Ignition OFF. Ignition ON, wait 10 seconds. CHECK the SODL or SODR Diagnostic Trouble Codes (DTCs), if DTC U0300:00 is retrieved again, INSTALL a new SODL or SODR . Refer to: SIDE OBSTACLE DETECTION CONTROL MODULE .
U0422:68	Invalid Data Received from Body Control Module: Event Information	This DTC sets when the SODL or SODR receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM . Refer to: BODY CONTROL MODULE (BCM) .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	The SODL or SODR is not configured. CONFIGURE the SODL or SODR . Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	The SODL or SODR is not configured. CONFIGURE the SODL or SODR . Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
U3000:44	Control Module: Data Memory Failure	Go to PINPOINT TEST H
U3000:45	Control Module: Program Memory Failure	Go to PINPOINT TEST H
U3000:46	Control Module: Calibration/Parameter Memory Failure	Go to PINPOINT TEST H
U3000:47	Control Module: Watchdog/Safety Microcontroller Failure	CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the SODL or SODR self-test. If DTC U3000:47 is retrieved again, INSTALL a new SODL or SODR . Refer to: SIDE OBSTACLE DETECTION CONTROL MODULE .
U3000:48	Control Module: Supervision Software Failure	Go to PINPOINT TEST H
U3000:49	Control Module: Internal Electronic Failure	Go to PINPOINT TEST H
U3000:4A	Control Module: Incorrect Component Installed	Go to PINPOINT TEST H
U3003:62	Battery Voltage: Signal Compare Failure	Go to PINPOINT TEST I