Occupant Classification System Module (OCSM)

OCSM DTC CHART

DTC	Description	Action
B0061:11	Passenger Seatbelt Tension Sensor: Circuit Short To Ground	Refer to: PINPOINT TEST - DTC: LL .
B0061:12	Passenger Seatbelt Tension Sensor: Circuit Short To Battery	Refer to: PINPOINT TEST - DTC: LL .
B0061:13	Passenger Seatbelt Tension Sensor: Circuit Open	Refer to: PINPOINT TEST - DTC: LL .
B0061:1C	Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range	Refer to: PINPOINT TEST - DTC: LL .
B0061:49	Passenger Seatbelt Tension Sensor: Internal Electronic Failure	Refer to: PINPOINT TEST - DTC: LL .
B00C0:11	Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C0:1A	Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C0:49	Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C1:11	Passenger Seat Occupant Classification Sensor "B": Circuit Short to Ground	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C1:12	Passenger Seat Occupant Classification Sensor "B": Circuit Short to Battery	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C1:49	Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
B00C2:11	Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground	Refer to: PINPOINT TEST - DTC: MM .
B00C2:12	Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery	Refer to: PINPOINT TEST - DTC: MM .
B1193:00	Crash Event Storage Full and Locked: No Sub Type Information	CLEAR the OCSM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC B1193:00 returns, INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . Refer to: INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT .
U0100:00	Lost Communication with ECM/PCM A: No Sub Type Information	NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of the repair unless directed to do so in the pinpoint test. Refer to: PINPOINT TEST - DTC: GG .
U0151:00	Lost Communication with Restraints Control Module: No Sub Type Information	NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of the repair unless directed to do so in the pinpoint test. Refer to: PINPOINT TEST - DTC: HH .
U0401:00	Invalid Data Received from ECM/PCM A: No Sub Type Information	NOTE: This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of the repair unless directed to do so in a pinpoint test. CARRY OUT the PCM self-test. To diagnose PCM Diagnostic Trouble Codes (DTCs), Refer to the appropriate Engine article for the procedure. If the DTC is not listed in the appropriate service information, Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) .
U3000:46	Control Module: Calibration/Parameter Memory Failure	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
U3000:49	Control Module: Internal Electronic Failure	INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
U3000:54	Control Module: Missing Calibration	Using a diagnostic scan tool, CARRY OUT the OCS Reset. FOLLOW all instructions on the diagnostic scan tool. If the OCS Reset was not successful, VERIFY correct installation of the OCS . VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the OCS Reset and REPEAT the self-test. If the OCS Reset fails or DTC U3000:54 is still present, INSTALL a new OCS sensor. Refer to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	Refer to: PINPOINT TEST - DTC: JJ .
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	Refer to: PINPOINT TEST - DTC: JJ .