LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2012 >> Taurus SEL, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1111 (Seat System) >> Disassembly And Assembly >> Seat Backrest - Front, With Fold Flat >> Disassembly And Assembly

Disassembly And Assembly

WARNING: This page is about a different car, the 2007 Lincoln MKX and 2007 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Always carry or place a live air bag module with the air bag and deployment door/trim cover/tear seam pointed away from the body. Do not set a live air bag module down with the deployment door/trim cover/tear seam face down. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
WARNING: Never probe the electrical connectors on air bag, safety canopy or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
WARNING: If the seat side air bag cover has been damaged or separated from its mounting, or if the air bag material has been exposed, install a new seat side air bag module. Never try to repair the seat side air bag module. Failure to follow these instructions may result in the seat side air bag deploying incorrectly, which increases the risk of serious personal injury or death in a crash.
WARNING: To reduce the risk of accidental deployment, do not use any memory saver devices. Failure to follow this instruction may result in serious personal injury or death.
NOTE: The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Only the front passenger seat can come equipped with optional fold-flat backrest.

All seats 

  1. Position the seat to access all the seat track-to-floor bolts and the safety belt retractor belt anchor nut.
  2. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of SUPPLEMENTAL RESTRAINT SYSTEM .
  3. Remove the front seat. For additional information, refer to Seat - Front .
  4. Remove the front seat backrest. For additional information, refer to Seat Backrest - Front .
  5. Remove the LH and RH outer fold flat recliner covers.
    • Pull to release the clips.
    • Slide up to disengage the retainer and remove.
  6. Remove the 4 fold flat recliner-to-fold flat backrest frame bolts.
    • To install, tighten to 50 Nm (37 lb-ft).
    • If necessary, remove the fold flat recliner cable.
  7. Release the backrest trim cover lower J-clip.
    8. Fig 1: Identifying Backrest Trim Cover J-Clips
    GF0030874Courtesy of FORD MOTOR CO.
    NOTE: RH side shown, LH similar.
  8. Release the LH and RH backrest trim cover tether from the backrest frame.
    9. Fig 2: Identifying LH & RH Backrest Trim Cover Tether
    GF0030875Courtesy of FORD MOTOR CO.
  9. Pull out at the bottom and detach the 2 lower hard back panel pin-type retainers.
  10. Slide the hard back panel out of the backrest trim cover.
  11. Remove the head restraint.
    1. Using an appropriate tool, push in the hole, lift up on the head restraint and release one side of the head restraint.
    2. Push the release button and remove the head restraint.
    12. Fig 3: Locating Release Button On Head Restraint
    GF0030876Courtesy of FORD MOTOR CO.
    CAUTION: Always install a new slave head restraint guide.
  12. Pull out and remove the master and slave head restraint guides.
    13. CAUTION: When installing, make sure the side air bag module wiring harness is not pinched between the side air bag module and the backrest frame.
    NOTE: When installing the side air bag module, new bolts must be installed.
  13. Remove the side air bag module.
    • Remove the 2 side air bag module bolts.
      • To install, tighten to 23 Nm (17 lb-ft).
    • Remove the side air bag module with wire harness.
      • Detach any side air bag module wire harness retainers.
    14. CAUTION: Use care when separating the backrest trim cover from the hook-and-loop strips, or the hook-and-loop strips can be torn from the backrest foam pad.
    NOTE: A new heater mat will come attached on a new foam pad.
  14. Remove the backrest trim cover.
    • Invert the backrest trim cover in an inside out fashion to the wire in the backrest trim cover attached to the clips in the backrest foam pad.
      • Separate the hook-and-loop strips.
    • Separate the backrest trim cover wire from the clips in the backrest foam pad.
    • If equipped, feed out the backrest heater mat wire harness from the opening in the side of the backrest trim cover.
    • Remove the backrest trim cover.
  15. Separate the backrest frame from the backrest foam pad.
  16. To assemble, reverse the disassembly procedure.
  17. Install the front seat backrest. For additional information, refer to Seat Backrest - Front .
  18. Install the front seat and repower the SRS. If a passenger seat has been serviced, do not prove out the SRS at this time.  For additional information, refer to Seat - Front .

    19. Passenger seat 

  19. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test and prove out the SRS. For additional information, refer to the General Procedures portion of SUPPLEMENTAL RESTRAINT SYSTEM .
scientia non olet · About LEMON Manuals