DTC Chart(s)

WARNING: This page is about a different variant/trim than selected.

Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices.

REFER to: DIAGNOSTIC METHODS .

DTC CHART: GWM

DTC	Description	Action
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new GWM . REFER to Gateway Module A (GWM) .
U3000:44	Control Module: Data Memory Failure	PERFORM a GWM self-test. If DTC U3000:44 is retrieved, INSTALL a new GWM . REFER to: GATEWAY MODULE A (GWM) . If DTC U3000:44 is not retrieved, the module is operating correctly at this time. The concern may have been caused by an intermittent concern.
U3000:45	Control Module: Program Memory Failure	PERFORM a GWM self-test. If DTC U3000:45 is retrieved, INSTALL a new GWM . REFER to: GATEWAY MODULE A (GWM) . If DTC U3000:45 is not retrieved, the module is operating correctly at this time. The concern may have been caused by an intermittent concern.

DTC CHART: BCM

DTC	Description	Action
U0004	High Speed CAN Communication Bus (+) Low: No Sub Type Information	A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.
U0005	High Speed CAN Communication Bus (+) High: No Sub Type Information	A High Speed Controller Area Network (HS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AA
U0007	High Speed CAN Communication Bus (-) Low: No Sub Type Information	A High Speed Controller Area Network (HS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AA
U0008	High Speed CAN Communication Bus (-) High: No Sub Type Information	A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.
U0009	High Speed CAN Communication Bus (-) Shorted to Bus (+): No Sub Type Information	A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.
U0013	Medium Speed CAN Communication Bus (+) Low: No Sub Type Information	A Medium Speed Controller Area Network (MS-CAN) fault is either currently present or was present at a point in time. The BCM can report this DTC while a fault is present because the BCM communicates with the scan tool on the High Speed Controller Area Network (HS-CAN). If no Medium Speed Controller Area Network (MS-CAN) modules communicate, GO to PINPOINT TEST AC If all Medium Speed Controller Area Network (MS-CAN) modules currently communicate, CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.
U0014	Medium Speed CAN Communication Bus (+) High: No Sub Type Information	A Medium Speed Controller Area Network (MS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AC
U0016	Medium Speed CAN Communication Bus (-) Low: No Sub Type Information	A Medium Speed Controller Area Network (MS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AC
U0017	Medium Speed CAN Communication Bus(-) High: No Sub Type Information	A Medium Speed Controller Area Network (MS-CAN) fault is either currently present or was present at a point in time. The BCM can report this DTC while a fault is present because the BCM communicates with the scan tool on the High Speed Controller Area Network (HS-CAN). If no Medium Speed Controller Area Network (MS-CAN) modules communicate, GO to PINPOINT TEST AC If all Medium Speed Controller Area Network (MS-CAN) modules currently communicate, CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.
U0018	Medium Speed CAN Communication Bus (-) Shorted to Bus (+): No Sub Type Information	A Medium Speed Controller Area Network (MS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for additional information.