DTC Charts
NOTE:
Network DTCs (U-codes) are often a result of intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often sets network DTCs. Replacing a module to resolve a network DTC is unlikely to resolve the concern. To prevent repeat network DTC concerns, inspect all network wiring, especially connectors. Test the vehicle battery, refer to
BATTERY, BATTERY MOUNTING & BATTERY CABLES
Article.
NOTE:
Refer to DESCRIPTION AND OPERATION
, INTELLIGENT ACCESS (IA) WITH PUSH BUTTON START
Article
to review the procedures for achieving the various ignition states (ignition off, ignition in accessory, ignition on, ignition start) on vehicles with this feature.
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
COMMUNICATION NETWORK DTC CHART
| DTC | Description | Source | Action |
|---|---|---|---|
| U0001:88 | High Speed CAN Communication Bus: Bus Off | Cruise-Control Module (C-CM) Power Steering Control Module (PSCM) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0002:88 | High Speed CAN Communication Bus Performance: Bus Off | Instrument Panel Cluster (IPC) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0011:88 | Medium Speed CAN Communication Bus Performance: Bus Off | IPC | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0028:08 | Vehicle Communication Bus A: Bus Signal / Message Failures | Restraints Control Module (RCM) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0028:88 | Vehicle Communication Bus A: Bus Off | RCM | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0073 | Control Module Communication Bus A Off | ABS module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0074 | Control Module Communication Bus B Off | ABS module | REFER to ANTI-LOCK BRAKE SYSTEM - VEHICLE DYNAMIC SYSTEMS Article. |
| U0100 | Lost Communication With ECM/PCM 4X4 control module | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | Accessory Protocol Interface Module (APIM) C-CM IPC Occupant Classification System Module (OCSM) Power Steering Control Module (PSCM) RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | Remote Function Actuator (RFA) module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0102 | Lost Communication With Transfer Case Control Module (4X4CM) | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST H . |
| U0102:00 | Lost Communication With Transfer Case Control Module: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST H . |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | Head Up Display (HUD) module IPC ABS module RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST I . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | 4X4 control module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST B . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | APIM C-CM IPC PSCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST B . |
| U0131 | Lost Communication With Power Steering Control Module (PSCM) | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST D . |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST D . |
| U0140 | Lost Communication With Body Control Module (GEM) | Audio Control Module (ACM) Driver Door Module (DDM) Driver Seat Module (DSM) Front Controls Interface Module (FCIM) Front Display Interface Module (FDIM) Interior Lighting Control Module (ILCM) | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST U . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | ACM APIM Audio Digital Signal Processing (DSP) module FCIM Global Positioning System Module (GPSM) HVAC module IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST U . |
| U0140:87 | Lost Communication With Body Control Module): Missing Message | RFA module HVAC module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST U . |
| U0151 | Lost Communication With Restraints Control Module | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST E . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | APIM IPC OCSM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST E . |
| U0154:00 | Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information | IPC RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST F . |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Module | 4X4 control module ABS module ACM DSM FDIM GPSM Smart Junction Box (SJB) | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | ACM APIM Audio DSP module C-CM HUD module HVAC module RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | RFA module HVAC module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | C-CM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST G . |
| U0159 | Lost Communication With Parking Assist Control Module (PAM) | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST J . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | ACM IPC PSCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST J . |
| U0161:00 | Lost Communication With Compass Module: No Sub Type Information | IPC | REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES Article. |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | ACM | REFER to INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM Article. |
| U0163:00 | Lost Communication With Navigation Control Module: No Sub Type Information | HVAC module IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST N . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | FCIM FDIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST V . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST V . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | APIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST P . |
| U0184 | Lost Communication With Radio (ACM) | FCIM FDIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST M . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | APIM Audio DSP module FCIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST M . |
| U0197 | Lost Communication With Telephone Control Module | ACM FDIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST L . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | ACM Audio DSP module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST L . |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST T . |
| U0214:00 | Lost Communication With Remote Function Actuator: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST K . |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST R . |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST S . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP) | FDIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST W . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST W . |
| U0242:00 | Lost Communication With Headlamp Control Module "B": No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST Y . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST L . |
| U0255 | Lost Communication With Front Controls Interface Module | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST N . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | ACM | APIM CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST O . |
| U0256 | Lost Communication With Front Display Interface Module | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST O . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | ACM APIM HVAC module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST N . |
| U0401 | Invalid Data Received from ECM/PCM A | 4X4 control module | RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | OCSM PSCM RCM | RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0401:68 | Invalid Data Received from ECM/PCM A: Event Information | C-CM IPC | RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0405 | Invalid Data Received from Cruise Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the C-CM. |
| U0405:55 | Invalid Data Received from Cruise Control Module: Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the C-CM. |
| U0405:68 | Invalid Data Received from Cruise Control Module: Event Information | HUD module | RETRIEVE and FOLLOW the DTCs from the C-CM. |
| U0415 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module | 4X4 control module | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | PSCM | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0418:68 | Invalid Data Received from Brake System Control Module: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0420 | Invalid Data Received From Power Steering Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the PSCM. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | APIM GPSM | RETRIEVE and FOLLOW the DTCs from the SJB. |
| U0422:55 | Invalid Data Received From Body Control Module: Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the SJB. |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the SJB. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | APIM GPSM | RETRIEVE and FOLLOW the DTCs from the IPC. |
| U0423:68 | Invalid Data Received From Instrument Panel Cluster Control Module: Event Information | HUD module HVAC module RFA module | RETRIEVE and FOLLOW the DTCs from the IPC. |
| U0424:68 | Invalid Data Received From HVAC Control Module: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the HVAC module. |
| U0430:68 | Invalid Data Received From Tire Pressure Monitor Module: Event Information | IPC | RETRIEVE and FOLLOW the DTCs from the SJB. |
| U0452 | Invalid Data Received from Restraints Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the RCM. |
| U0459:68 | Invalid Data Received from Head Up Display: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the HUD module. |
| U045A:00 | Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information | PSCM | RETRIEVE and FOLLOW the DTCs from the PAM. |
| U045A:55 | Invalid Data Received From Parking Assist Control Module "A": Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the PAM. |
| U045A:68 | Invalid Data Received From Parking Assist Control Module "A": Event Information | IPC | RETRIEVE and FOLLOW the DTCs from the PAM. |
| U0462:68 | Invalid Data Received From Compass Module: Event Information | IPC | REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES Article. |
| U0464:68 | Invalid Data Received From Navigation Control Module: Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the ACM. |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | APIM | RETRIEVE and FOLLOW the DTCs from the GPSM. |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | APIM | RETRIEVE and FOLLOW the DTCs from the ACM. |
| U049A:68 | Invalid Data Received from "Door Control Module A": Event Information | RFA module | RETRIEVE and FOLLOW the DTCs from the DDM. |
| U0515:56 | Invalid Data Received from RFA Module | IPC | RETRIEVE and FOLLOW the DTCs from the RFA module. |
| U0554:00 | Invalid Data Received from Accessory Protocol Interface Module: No Sub Type Information | RCM | RETRIEVE and FOLLOW the DTCs from the APIM. |
| U0557:68 | Invalid Data Received From Front Controls Interface Module "A": Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the FCIM. |
| U2023 | Fault Received From External Node | ABS module | The module had an invalid network input/message from another module. RETRIEVE and FOLLOW the non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULE Article. |
| U2472 | Unexpected Ignition State | SJB | REFER to MULTIFUNCTION ELECTRONIC MODULE Article. |
| U2473 | Unexpected Vehicle Speed (VSS) | SJB | REFER to MULTIFUNCTION ELECTRONIC MODULE Article. |
| U3000:88 | Control Module: Bus Off | APIM | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |