Body Control Module (BCM)
BODY CONTROL MODULE (BCM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1115: 11 | High Mounted Stop Lamp Control: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B123A: 11 | Left Front Turn Indicator: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B123A: 15 | Left Front Turn Indicator: Circuit Short To Battery or Open | GO to PINPOINT TEST M . |
| B123B: 11 | Right Front Turn Indicator: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B123B: 15 | Right Front Turn Indicator: Circuit Short To Battery or Open | GO to PINPOINT TEST M . |
| B1277: 11 | Reverse Lamp: Circuit Short To Ground | GO to PINPOINT TEST U . |
| B1277: 15 | Reverse Lamp: Circuit Short To Battery or Open | If the reverse lamps are inoperative, GO to PINPOINT TEST U
. If the reverse lamps are always on, GO to PINPOINT TEST W . |
| B130C: 12 | Load Shed Control: Circuit Short To Battery | GO to PINPOINT TEST AC . |
| B130C: 14 | Load Shed Control: Circuit Short To Ground or Open | GO to PINPOINT TEST AC . |
| B132B: 11 | Left Stop/Turn Lamp: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B132B: 15 | Left Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to PINPOINT TEST J
. If the stoplamp is always on, GO to PINPOINT TEST K . |
| B132C: 11 | Right Stop/Turn Lamp: Circuit Short To Ground | GO to PINPOINT TEST J . |
| B132C: 15 | Right Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to PINPOINT TEST J
. If the stoplamp is always on, GO to PINPOINT TEST K . |
| B1A85: 11 | Ambient Light Sensor: Circuit Short To Ground | GO to PINPOINT TEST H . |
| B1A85: 13 | Ambient Light Sensor: Circuit Open | GO to PINPOINT TEST H . |
| B1C98: 11 | Left Corner Lamp Circuit: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B1C99: 11 | Right Corner Lamp Circuit: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B1D00: 11 | Left Low Beam: Circuit Short To Ground | GO to PINPOINT TEST A . |
| B1D01: 11 | Right Low Beam: Circuit Short To Ground | GO to PINPOINT TEST A . |
| B1D02: 11 | Left High Beam Circuit: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B1D02: 15 | Left High Beam Circuit: Circuit Short To Battery or Open | If the high beam is inoperative, GO to PINPOINT TEST B
. If the high beam is always on, GO to PINPOINT TEST D . |
| B1D03: 11 | Right High Beam Circuit: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B1D03: 15 | Right High Beam Circuit: Circuit Short To Battery or Open | If the high beam is inoperative, GO to PINPOINT TEST B
. If the high beam is always on, GO to PINPOINT TEST D . |
| B1D35: 11 | Hazard Switch: Circuit Short To Ground | GO to PINPOINT TEST N . |
| C0040: 12 | Brake Pedal Switch "A": Circuit Short To Battery | GO to PINPOINT TEST K . |
| U1000: 00 | Solid State Driver Protection Active - Driver Disabled: No Sub Type Information | The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Body Control Module (BCM) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test. |
| U3000: 49 | Control Module: Internal Electronic Failure | The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new BCM . REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |