LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2011 >> Mustang Base, 2D Convertible, Standard >> Repair and Diagnosis >> Body & Frame >> Sun Roof/T-Top/Convertible Top >> Removal And Installation >> Convertible Top Assembly >> Installation

Convertible Top Assembly: Installation

    NOTE: Use care when cutting the tie straps or damage to the convertible top material may occur.
  1. Cut and remove the No. 5 bow and side rail tie straps.
    2. NOTE: Do not compress the convertible top frame No. 5 bow more than necessary to install it to the vehicle. Excessive compression can damage the convertible top frame No. 5 bow.
  2. With an assistant, position the convertible top assembly into the vehicle.
    • If necessary, compress the convertible top frame No. 5 bow approximately 80 cm (3.14 in).
  3. Slowly release the convertible top frame No. 5 bow, while aligning the guide pins on the convertible top frame with the holes in the rear quarter panels.
  4. Install the LH and RH convertible top frame No. 5 bow pivot bolts.
    • Tighten to 9 Nm (80 lb-in).
  5. Position the water diverters as shown in illustration, making sure the edges overlap completely, and the diverters are not caught between the brackets and the body.
    Fig 1: Locating Water Diverters Position
    G06393254Courtesy of FORD MOTOR CO.
  6. Install the LH and RH pivot bracket bolts.
    • Tighten to 48 Nm (35 lb-ft).
  7. Operate the convertible top by hand, to make sure the top operates freely, without binding.
  8. Position the LH and RH hydraulic lift cylinders.
  9. Install the LH and RH clevis-to-hydraulic lift cylinder rod bolts.
    • Tighten to 20 Nm (177 lb-in).
  10. Install the LH and RH hydraulic lift cylinder brackets and bolts.
    • Tighten to 20 Nm (177 lb-in).
  11. Connect the convertible top ajar switch electrical connector.
    12. NOTE: RH pivot bracket bolts and pivot bracket-to-quarter panel bracket bolts are shown in illustration, LH pivot bracket bolts and pivot bracket-to-quarter panel bracket bolts are similar.
    Fig 2: Locating Pivot Bracket-To-Quarter Panel Bracket Bolts
    G06393255Courtesy of FORD MOTOR CO.
  12. Using the convertible top switch, raise and latch the convertible top to check for correct alignment and latching.

    If the convertible top is not aligned or does not latch correctly, carry out the steps in the following sequence:

    1. Fully lower the convertible top.
    2. Loosen the 6 LH and RH pivot bracket bolts.
    3. Loosen the 4 LH and RH pivot bracket-to-quarter panel bracket bolts.
    4. Fully raise and latch the convertible top.
    5. Tighten the 4 LH and RH pivot bracket-to-quarter panel bracket bolts.
      • Tighten to 11 Nm (97 lb-in).
    6. Tighten the 6 LH and RH pivot bracket bolts.
      • Tighten to 48 Nm (35 lb-ft).
    7. Fully lower the convertible top.
  13. Install the LH and RH bolts attaching the L-brackets to the quarter panel.
    • Tighten to 27 Nm (20 lb-ft).
  14. Install the LH and RH inner quarter window belt line seals.
  15. Install the LH and RH rear quarter trim panels. For additional information, refer to INTERIOR TRIM & ORNAMENTATION article.
    16. NOTE: Use care when cutting the tie straps or damage to the convertible top material may occur.
  16. Cut and remove the well sling tie strap.
  17. Fully raise the convertible top.
  18. Recheck the position of the water diverters, and adjust as necessary for correct placement.
  19. Connect the rear window defrost electrical connector.
  20. Install the rear seat backrest. For additional information, refer to SEAT SYSTEM article.
  21. Position the well sling channel and install the 4 pin-type retainers to the rear seat backrest.
  22. Make sure the door glass and quarter glass correctly seal against the convertible top side rail. If adjustment is necessary, refer to WINDOWS & GLASS - GLASS, FRAMES & MECHANISMS article.
scientia non olet · About LEMON Manuals