Common Specs & Procedures
FIAT 124 SPIDER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Hub and Bearing to Knuckle Bolts | |||
| Front | 96 ft. lbs. (130 N.m) | ||
| Axle Nut/Hub Nut | |||
| Rear | 92 ft. lbs. + 180° + 188 ft. lbs. (125 N.m + 180° + 255 N.m) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BASE BRAKES BLEEDING PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | Refer to TECHNICAL SPECIFICATIONS . | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | GENERATOR | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | 14-18 psi (97-124 kPa) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | PUMP, WATER | ||
| Engine Mechanical | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil Pressure | Pressure @ Curb Idle Speed: > 10 psi (> 0.7 bar), Pressure @ 4000 RPM: > 58 psi (> 4.0 bar): At Normal Operating Temperatures | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Flexplate | Refer to REMOVAL AND INSTALLATION | ||
| Flywheel | Refer to REMOVAL AND INSTALLATION . | ||
| Fuel System | |||
| Pressure Specification | 58 psi (407 kPa) +/- 3 psi (34 kPa) | ||
| Fuel Pressure Test Procedure | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | Information not available from manufacturer. | ||
| Fuel Filter R & I | Information not available from manufacturer. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | The firing order is 1-3-4-2. For 16-valve, refer to FIRING ORDER & CYLINDER IDENTIFICATION . | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| Type | NGK SIKR9A7 | ||
| Gap | 0.023 - 0.027 in / 0.6 - 0.7 mm | ||
| Torque | 160 in. lbs. (18 N.m) | ||
| Starting | |||
| Starter | Information not available from manufacturer. | ||
| Torque | Torque specifications are in text under TORQUE SPECIFICATIONS . | ||
| Wheel Alignment | |||
| Adjustment Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | |||
| Front | TORQUE SPECIFICATIONS | ||
| Rear | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 94 ft. lbs. (128 N.m) | ||