LEMON Manuals: Even more car manuals for everyone
Home >> Eagle >> 1996 >> Summit DL, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 11 (1.8L 4-CYL. Engine - VIN [C]) >> General Engine Specifications

General Engine Specifications

WARNING: This page is about a different variant/trim than selected.
GENERAL SPECIFICATIONS

Application Specification
Displacement 111 Cu. In.
Bore 3.19" (81.0 mm)
Stroke 3.50" (89.0 mm)
Compression Ratio 8.5:1
Fuel System MFI/SFI
Horsepower @ RPM
California 111 @ 3000
Federal 113 @ 3000
Torque Ft. Lbs. @ RPM 116 @ 4500
CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS

Application In. (mm)
Crankshaft End Play
Standard .0020-.0071 (.051-.180)
Wear Limit .010 (.25)
Main Bearings
Journal Diameter 2.244 (57.00)
Journal Out-Of-Round .0006 (.015)
Journal Taper .0002 (.005)
Oil Clearance-Standard .0008-.0016 (.020-.040)
Oil Clearance-Wear Limit .004 (.10)
Connecting Rod Bearings
Journal Diameter 1.771 (45.00)
Journal Out-Of-Round .0006 (.015)
Journal Taper .0002 (.005)
Oil Clearance-Standard .0008-.0020 (.020-.050)
Oil Clearance-Wear Limit .004 (.10)
CONNECTING RODS

Application In. (mm)
Maximum Bend (1) .0020 (.051)
Maximum Twist (1) .0039 (.01)
Side Play
Standard .0039-.0098 (.010-.250)
Wear Limit .016 (.41)
(1) Per 3.937" (100 mm).
PISTONS, PINS & RINGS

Application In. (mm)
Pistons
Clearance .0008-.0016 (.020-.040)
Diameter 3.19 (81.0)
Pins
Rod Fit (1)
Ring No. 1
End Gap-Standard .0098-.0157 (.250-.400)
End Gap-Wear Limit .031 (.79)
Side Clearance-Standard .0012-.0028 (.030-.070)
Side Clearance-Wear Limit .004 (.10)
Ring No. 2
End Gap-Standard .0157-.0217 (.400-.550)
End Gap-Wear Limit .031 (.79)
Side Clearance-Standard .0008-.0024 (.020-.060)
Side Clearance-Wear Limit .004 (.10)
Oil Ring Side Rail .0079-.0236 (.200-.600)
(1) Press fit with load of 1100-3300 lbs. (499-1497 kg).
CYLINDER BLOCK

Application In. (mm)
Cylinder Bore
Standard Diameter 3.19 (81.0)
Maximum Taper .0004 (.010)
Maximum Out-Of-Round .0004 (.010)
Deck Height 10.370-10.379 (263.4-263.6)
Maximum Deck Warpage (1) .0039 (.099)
(1) Combined maximum total grind limit of cylinder head and cylinder block is .008" (.20 mm).
VALVES & VALVE SPRINGS

Application Specification
Intake Valves
Face Angle 45-45.5°
Minimum Margin .019" (.48 mm)
Stem Diameter .235" (5.97 mm)
Exhaust Valves
Face Angle 45-45.5°
Minimum Margin .039" (1.00 mm)
Stem Diameter .234" (5.95 mm)
Valve Springs
Free Length 1.965-2.004" (48.21-49.20 mm)
Installed Height 1.74 (44.2)
Out-Of-Square-Standard Less Than 2°
Out-Of-Square-Wear Limit 4°
CYLINDER HEAD

Application Specification
Cylinder Head Height 4.720" (119.90 mm)
Maximum Warpage (1) .0012" (.030 mm)
Valve Seats
Intake Valve-Seat Angle 43.5-44.0°
Intake Valve-Seat Width .0354-.0512" (.899-1.300 mm)
Exhaust Valve-Seat Angle 43.5-44.0°
Exhaust Valve-Seat Width .0354-.0512" (.899-1.300 mm)
Valve Guides - Intake Valve
Valve Stem-To-Guide Oil Clearance (Standard) .0008-.0020" (.020-.050 mm)
Valve Stem-To-Guide Oil Clearance (Wear Limit) .004" (.10 mm)
Valve Guides - Exhaust Valve
Valve Stem-To-Guide Oil Clearance (Standard) .0020-.0035" (.050-.090 mm)
Valve Stem-To-Guide Oil Clearance (Wear Limit) .006" (.15 mm)
(1) Combined maximum total grind limit of cylinder head and cylinder block is .008" (.20 mm).
CAMSHAFT

Application In. (mm)
End Play .004-.008 (.10-.20)
Journal Diameter 1.7689-1.7693 (44.930-44.940)
Lobe Height
Intake 1.4677-1.4876 (37.280-37.780)
Exhaust 1.4799-1.4996 (37.590-38.090)
Oil Clearance .0020-.0035 (.051-.089)
scientia non olet · About LEMON Manuals