Common Specs & Procedures
DURANGO COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 229 ft. lbs. (310 N.m) | ||
| Rear | 229 ft. lbs. (310 N.m) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: STANDARD PROCEDURE , Antilock Brakes: STANDARD PROCEDURE - ABS SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | Base Brakes: SPECIFICATIONS , Antilock Brakes: TECHNICAL SPECIFICATIONS | ||
| Torque | Base Brakes: TORQUE SPECIFICATION , Antilock Brakes: TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR RATINGS | ||
| Torque | TORQUE SPECIFICATION | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Accessory Drive Belt Routing" figure under 3.6L, 5.7L and 6.4L INSTALLATION or 6.2LINSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | 3.6L, 5.7L and 6.4L SPECIFICATIONS or 6.2LSPECIFICATIONS | ||
| Radiator Cap Pressure | 16-20 psi (110-138 kPa) | ||
| Thermostat R & I | 3.6L, 5.7L and 6.4L THERMOSTAT or 6.2LTHERMOSTAT | ||
| Water Pump R & I | 3.6L, 5.7L and 6.4L PUMP, WATER or 6.2LPUMP, WATER | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | CYLINDER COMPRESSION TEST | ||
| Oil Pressure | Refer to OIL PRESSURE table under ENGINE SPECIFICATIONS . | ||
| Overhaul | ENGINE SPECIFICATIONS , | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 5.7L | |||
| Compression | CYLINDER COMPRESSION TEST | ||
| Oil pressure | OIL PRESSURE | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 6.2L | |||
| Compression | NA | ||
| Oil pressure | Refer to OIL PRESSURE table under ENGINE SPECIFICATIONS | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 6.4L | |||
| Compression | CYLINDER COMPRESSION TEST | ||
| Oil pressure | Refer to OIL PRESSURE table under ENGINE SPECIFICATIONS | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 70 ft. lbs. (95 N.m) | ||
| Fuel System | |||
| Pressure Specification | 58 psi +/- 2 psi. | ||
| Fuel Pressure Test Procedure | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | |||
| 3.6L | MODULE, FUEL PUMP | ||
| 5.7L | MODULE, FUEL PUMP | ||
| 6.2L | MODULE, FUEL PUMP | ||
| 6.4L | MODULE, FUEL PUMP | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION . | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 3.6L | |||
| Type | Recommended to use Mopar spark plugs | ||
| Gap | .043 in. (1.1 mm) | ||
| Torque | 15 ft. lbs. (20 N.m) | ||
| 5.7L | |||
| Type | Recommended to use Mopar spark plugs | ||
| Gap | .043 in. (1.1 mm) | ||
| Torque | 18 ft. lbs. (25 N.m) | ||
| 6.2L | |||
| Type | Recommended to use Mopar spark plugs | ||
| Gap | .031 in. (0.8 mm) | ||
| Torque | 18 ft. lbs. (25 N.m) | ||
| 6.4L | |||
| Type | Recommended to use Mopar spark plugs | ||
| Gap | .043 in. (1.1 mm) | ||
| Torque | 11 ft. lbs. (15 N.m): Torque critical tapered design. Do not exceed 15 ft. lbs. (21 N.m) | ||
| Starting | |||
| Starter | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Front: TORQUE SPECIFICATIONS , Rear: TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Base: 130 Ft-Lbs (176 N.m) SRT: 110 Ft-Lbs (149 N.m) |
||