Diagnostic Test

DTC IS ACTIVE
NOTE:
Diagnose and repair any system voltage DTCs before continuing with this test.

NOTE:
Diagnose and repair any communication DTCs before continuing with this test.
1. Start the engine and allow it to reach operating temperature.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hand near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
2. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go To 2.
  No
  - Perform the CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. Refer to CHECKING FOR AN INTERMITTENT DTC .
(N5) FUEL LEVEL SIGNAL 2 CIRCUIT SHORTED TO VOLTAGE

Fig 1: Checking Fuel Level Signal 2 Circuit For A Short To Voltage
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the Fuel Tank Module harness connector.
3. Disconnect the C2 Cluster (CCN) harness connector.
4. Turn the ignition on.
5. Measure the voltage of the (N5) Fuel Level Signal 2 circuit in the Fuel Tank Module harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the short to voltage in the (N5) Fuel Level Signal 2 circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3.
(N5) FUEL LEVEL SIGNAL 2 OPEN OR HIGH RESISTANCE

Fig 2: Checking Fuel Level Signal 2 Circuit For Open Circuit Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Measure the resistance of the (N5) Fuel Level Signal 2 circuit between the Fuel Tank Module harness connector and the C2 Cluster (CCN) harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go To 4.
  No
  - Repair the open or high resistance in the (N5) Fuel Level Signal 2 circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
(Z210) GROUND CIRCUIT OPEN OR HIGH RESISTANCE

Fig 3: Checking Ground Circuit For Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Connect the C2 Cluster (CCN) harness connector.
2. Using a 12-volt test light connected to 12 volts, check the (Z210) Ground circuit in the Fuel Tank Module harness connector.
  NOTE:
  The test light should be illuminated and bright. Compare the brightness to that of a direction to the battery.
  
  Is the test light illuminated and bright?
  
  Yes
  - Go To 5.
  No
  - Repair the open or high resistance in the (Z210) Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
FUEL TANK WIRING HARNESS INSPECTION
WARNING:
When the engine is operating, do not stand in direct line with the fan. Do not put your hand near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
1. Remove the fuel tank in accordance with the Service Information.
2. Inspect the wiring and connectors between the Fuel Tank Module harness connector and the Fuel Level Sensor 2 connector.
3. Look for any chafed, pierced, pinched, shorted or broken wires.
4. Look for broken, bent, pushed out or corroded terminals.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 6.
FUEL LEVEL SENSOR 2
1. Connect the Fuel Tank Module harness connector.
2. Connect a jumper wire between ground and the (N5) Fuel Level Signal 2 circuit in the Fuel Level Sensor 2 harness connector.
3. Turn the ignition on.
4. With the scan tool, read the Fuel Tank Module signal voltage.
  NOTE:
  The sensor voltage should be approximately 0.0 volts (plus or minus.1 of a volt) with the jumper wire in place.
  
  Does the scan tool display the voltage as described above?
  
  Yes
  - Replace the Fuel Level Sensor 2 in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 7.
CLUSTER (CCN)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Fuel Level Sensor 2 harness connector and the Cluster (CCN).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Perform any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Replace and program the Cluster (CCN) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .