LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2000 >> Durango 5.2 Y >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Body Control Modules >> System Tests >> Communications >> Not Receiving Bus Messages Correctly

Not Receiving Bus Messages Correctly

CAUTION: Always turn ignition switch to OFF position prior to disconnecting any module connector or battery.
  1. On models equipped with manual transmission, go to next step. On models with automatic transmission, turn ignition switch to OFF position. Disconnect Transmission Control Module (TCM). Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace TCM. See appropriate ELECTRONIC CONTROLS article in AUTOMATIC TRANSMISSIONS.
  2. Turn ignition switch to OFF position. Disconnect Powertrain Control Module (PCM). Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace PCM. See POWERTRAIN CONTROL MODULE (PCM) VERIFICATION TEST  .
  3. Turn ignition switch to OFF position. Disconnect Controller Anti-lock Brake (CAB) module. Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace CAB module. Perform CONTROLLER ANTI-LOCK BRAKE (CAB) VERIFICATION TEST  .
  4. If not equipped with Compass Mini Trip Computer (CMTC), go to next step. Turn ignition switch to OFF position. Disconnect CMTC. Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace CMTC. Perform BODY VERIFICATION TEST  .
  5. Turn ignition switch to OFF position. Disconnect radio 2-pin connector C3. Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace radio. Perform BODY VERIFICATION TEST  .
  6. Turn ignition switch to OFF position. Disconnect Central Timer Module (CTM). Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace CTM. Perform BODY VERIFICATION TEST  .
  7. Turn ignition switch to OFF position. Disconnect Mechanical Instrument Cluster (MIC). Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace MIC. Perform BODY VERIFICATION TEST  .
  8. Turn ignition switch to OFF position. Disconnect negative battery cable. Wait 2 minutes. Disconnect Air Bag Control Module (ACM). Connect negative battery cable. Turn ignition switch to ON position. If scan tool displays same CCD bus failure message, go to next step. If CCD bus failure message changes, check all connectors for good terminal contact. Repair connectors as necessary. If connectors are okay, replace ACM. Perform AIR BAG VERIFICATION TEST  .
  9. Turn ignition switch to OFF position. Disconnect negative battery cable. Connect all previously disconnected connectors and inspect connectors for good terminal contact. Repair connectors as necessary. Connect negative battery cable. Turn ignition switch to ON position. If CCD bus failure message changes, fault is not present at this time. If scan tool displays same CCD bus failure message, repair or replace scan tool or scan tool cable(s) as necessary. Perform BODY VERIFICATION TEST  .
scientia non olet · About LEMON Manuals