LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> Sebring Base, 2D Convertible, ED3 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 17 (Powertrain Control Module (Pcm) - Electrical Diagnostics - 62TE Automatic Transmission) >> DTC Troubleshooting >> P2763-Torque Converter Clutch Pressure Control Circuit High >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. CHECK IF DTC IS CURRENT 
    1. With the scan tool, view DTCs.

      Is the status Active or is the Starts Since Set counter 2 or less for this DTC?

      Yes 

      • Go to step  2

      No 

      • Go to step  7
  2. CHECK THE (T84) EMCC VFS CONTROL CIRCUIT FOR AN OPEN 
    1. Turn the ignition off to the lock position.
    2. Disconnect the Transmission Solenoid/TRS Assembly harness connector.
    3. Disconnect the PCM C4 harness connector.
      NOTE: Check connectors - Clean/repair as necessary.
    4. Measure the resistance of the (T84) EMCC VFS Control circuit between the Transmission Solenoid Assembly harness connector and the PCM C4 harness connector.

      Is the resistance below 5.0 ohms?

      Yes 

      • Go to step  3

      No 

  3. CHECK THE (T84) EMCC VFS CONTROL CIRCUIT FOR A SHORT TO GROUND 
    1. Measure the resistance between ground and the (T84) EMCC VFS Control circuit.

      Is the resistance below 100k ohms?

      Yes 

      No 

      • Go to step  4
  4. CHECK THE (T84) EMCC VFS CONTROL CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Ignition on, engine not running.
    2. Measure the voltage of the (T84) EMCC VFS Control circuit.

      Is the voltage above 0.5 volt?

      Yes 

      No 

      • Go to step  5
  5. CHECK THE (T84) EMCC VFS CONTROL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT 
    1. Turn the ignition off to the lock position.
    2. Measure the resistance between the (T84) EMCC VFS Control circuit and all other circuits in the Transmission Solenoid/TRS Assembly harness connector.

      Is the resistance below 100k ohms between the (T84) EMCC VFS Control circuit and any other circuit in the Transmission Solenoid Assembly harness connector?

      Yes 

      No 

      • Go to step  6
  6. CHECK THE EMCC VFS SOLENOID 
    1. Turn the ignition off to the lock position.
    2. Measure the resistance of the EMCC VFS Solenoid between the (T84) EMCC VFS Control and the (T16) Transmission Control Output on the Transmission Solenoid/TRS Assembly connector.

      Is the resistance of the EMCC VFS SOLENOID 5.0 ohms (± 0.5 ohms) at 21°C (70°F)?

      Yes 

      • Using the schematics as a guide, check the Transmission Control Module (TCM) pins, terminals, and connectors for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace and program the TCM per the Service Information.
      • Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure 

      No 

  7. CHECK WIRING AND CONNECTORS 
    1. The conditions necessary to set the DTC are not present at this time.
    2. Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.
    3. Wiggle the wires while checking for shorted and open circuits.
    4. Check for any Service Bulletins that may apply.

      Were there any problems found?

      Yes 

      No 

      • Test Complete.
scientia non olet · About LEMON Manuals