Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECKING FOR LOSS OF PRIME DTC
1. With the scan tool, read DTCs.
  Is the DTC P0944 present also?
  
  Yes
  - Refer to appropriate Transmission article and perform the appropriate diagnostic procedure.
  No
  - Go to step 2
CHECK FOR RELATED TRANSMISSION DTCS
1. With the scan tool, read DTCs.
  Are any of the DTCs P0732, P0734 and/or P084B present also?
  
  Yes
  - Replace the Transmission Solenoid/TRS Assembly per the Service Information.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 3
CHECK TO SEE IF DTC P084A IS CURRENT
1. With the scan tool, read DTCs.
  Is the status Active for this DTC or is the STARTS SINCE SET counter 2 or less?
  
  Yes
  - Go to step 4
  No
  - Go to step 9
PCM AND WIRING
1. Turn the ignition off to the lock position.
2. Remove the Ignition Switch Feed fuse from the TIPM.
  CAUTION: Removal of the Ignition Switch Feed fuse from the TIPM will prevent the vehicle from being started in gear.
  
  WARNING: The Ignition Switch Feed fuse must be removed from the TIPM. Failure to do so can result in possible serious or fatal injury.
3. Install the Transmission Simulator, Miller tool #8333A and the Electronic Transmission Adapter kit.
  NOTE: Check connectors - Clean/repair as necessary.
4. Ignition on, engine not running.
5. With the Transmission Simulator, turn the Pressure Switch selector switch to DC.
6. With the scan tool, monitor the DC Pressure Switch state while pressing the Pressure Switch Test button on the Transmission Simulator.
7. Wiggle the wires leading to the PCM while pressing and holding the Pressure Switch Test button.
  Did the DC Pressure Switch state change to closed and remain closed while wiggling the wires?
  
  Yes
  - Disassemble and inspect the Valve Body per the Service Information and repair or replace as necessary. If no problems are found in the Valve Body, replace the Transmission Solenoid/TRS Assembly.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 5
(T83) DC PRESSURE SIGNAL CIRCUIT OPEN

Fig 1: Checking DC Pressure Switch Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off to the lock position.
2. Disconnect the PCM C4 harness connector.
3. Disconnect the Transmission Solenoid/TRS Assembly harness connector.
  NOTE: Check connectors - Clean/repair as necessary.
  
  CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install PCM Pinout Box 8815 to perform diagnosis.
4. Measure the resistance of the (T83) DC Pressure Switch Sense circuit from the appropriate terminal of the Miller tool #8815 to the Transmission Solenoid/TRS Assembly harness connector.
  Is the resistance above 5.0 ohms?
  
  Yes
  - Repair the (T83) DC Pressure Switch Sense circuit for an open.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 6
(T83) DC PRESSURE SIGNAL CIRCUIT SHORT TO GROUND

Fig 2: Checking DC Pressure Switch Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between ground and the (T83) DC Pressure Switch Sense circuit.
  Is the resistance below 5.0 ohms?
  
  Yes
  - Repair the (T83) DC Pressure Switch Sense circuit for a short to ground.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 7
(T83) DC PRESSURE SIGNAL CIRCUIT SHORT TO VOLTAGE

Fig 3: Checking DC Pressure Switch Circuit
Courtesy of CHRYSLER LLC
1. Ignition on, engine not running.
2. With the scan tool in the TIPM, actuate the TCM output.
3. Measure the voltage of the (T83) DC Pressure Switch Sense circuit.
  Is the voltage above 0.5 volts?
  
  Yes
  - Repair the (T83) DC Pressure Switch Sense circuit for a short to voltage.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Go to step 8
TRANSMISSION CONTROL OUTPUT CIRCUIT OPEN

Fig 4: Checking Transmission Control Output Circuit
Courtesy of CHRYSLER LLC
1. While still actuating the TCM output in the TIPM and using a 12-volt test light connected to ground, check (T16) Transmission Control Output circuit in the Transmission Solenoid/TRS Assembly harness connector.
  NOTE: The test light must illuminate brightly. Compare the brightness to that of a direct connection to the battery.
  
  Does the test light illuminate brightly?
  
  Yes
  - Replace and program the Powertrain Control Module per the Service Information. With the scan tool perform QUICK LEARN.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Repair the Transmission Control Output circuit for an open or high resistance. If the fuse is open make sure to check for a short to ground.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
INTERMITTENT WIRING AND CONNECTORS
1. The conditions necessary to set the DTC are not present at this time.
2. Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.
3. Wiggle the wires while checking for shorted and open circuits.
4. With the scan tool, check the DTC EVENT DATA to help identify the conditions in which the DTC was set.
  Were there any problems found?
  
  Yes
  - Repair as necessary.
  - Perform 62TE VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
  No
  - Test Complete.