Diagnostic Test

CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT CLASSIFICATION MODULE (OCM)
NOTE: Ensure that the battery is fully charged.
1. Turn the ignition on, then off, and then on again.
2. With the scan tool, read Occupant Classification Module (OCM) DTCs.
  Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?
  
  Yes
  - Diagnose and repair the DTCs. For a complete list of symptoms. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Diagnosis and Testing .
  No
  - Go to step 2
VERIFY THAT DTC B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE IS ACTIVE
1. With the scan tool, read OCM DTCs.
  Does the scan tool display active: B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE?
  
  Yes
  - Go to step 3
  No
  - Go to step 1
INSPECT PASSENGER SEAT HARNESS WIRES AND CONNECTORS
WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Using the SYSTEM WIRING DIAGRAMS as a guide, inspect the Passenger Seat Harness wiring and connectors. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.
  Are any of these conditions present?
  
  Yes
  - Replace the Passenger Seat Harness in accordance with the Service Information.
  - Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Standard Procedure .
  - Perform AIRBAG SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .
  No
  - Go to step 4
PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
NOTE: Failure to follow test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: Verify That All Tests Steps That Led You Here Were Performed As Directed; Verify That The Ignition Is In Run; Wait 30 Seconds After Changing The Seat Weight Before Proceeding To Allow The System To Stabilize; Only Press Scan Tool Buttons When Directed To Do So; and Perform The Occupant Classification Module System Verification Test To Completion.
1. With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, wait two minutes, and then proceed as follows. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Standard Procedure .
2. With the scan tool, read OCM DTCs.
  Does the scan tool display any active PASSENGER SEAT WEIGHT SENSOR PERFORMANCE DTCs?
  
  Yes
  - Go to step 5
  No - But Other DTCs Present
  - Diagnose and repair the DTCs. For a complete list of symptoms. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Diagnosis and Testing .
  No - No Active DTCs Present
  - Perform AIRBAG SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .
PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Verify that all of the Seat Weight Sensor mounting screws are torqued to specification. Refer to Body - Specifications .
  WARNING: Turn the ignition on, then reconnect the 12-volt battery. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
  
  NOTE: Failure to follow test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: Verify That All Tests Steps That Led You Here Were Performed As Directed; Verify That The Ignition Is In Run; Wait 30 Seconds After Changing The Seat Weight Before Proceeding To Allow The System To Stabilize; Only Press Scan Tool Buttons When Directed To Do So; and Perform The Occupant Classification Module System Verification Test To Completion.
2. With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, wait two minutes, and then proceed as follows. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Standard Procedure .
3. With the scan tool, read OCM DTCs.
  Does the scan tool display any active PASSENGER SEAT WEIGHT SENSOR PERFORMANCE DTCs?
  
  Yes
  - Perform the DIAGNOSIS AND CHECKOUT PROCEDURE FOR SEAT WEIGHT SENSORS . Refer to Non-DTC Diagnostics/Restraints - Diagnosis and Testing .
  No - But Other DTCs Present
  - Diagnose and repair the DTCs. For a complete list of symptoms. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Diagnosis and Testing .
  No - No Active DTCs Present
  - Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

CHECKING STORED OR INTERMITTENT CODES
NOTE: Diagnose and repair all active codes before diagnosing stored codes. Refer to DIAGNOSTIC CODE INDEX for a complete list of airbag system diagnostic procedures.
1. With the scan tool, record and erase all Airbag System Module DTCs.
  WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
2. Using the SYSTEM WIRING DIAGRAMS as a guide, inspect the related wiring and connectors for chafed, pierced, pinched, and partially broken wires, and for broken, bent, pushed out, corroded, and contaminated terminals. Repair as necessary.
3. Reconnect all disconnected components and harness connectors.
  WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
4. With the scan tool, monitor for active codes while performing the following:
  WARNING: Maintain a safe distance from all airbags while performing the following steps. Failure to follow these instructions may result in possible serious or fatal injury.
  - Wiggle the wiring harness and connectors of the related airbag circuit.
  - Continue the test until either a code becomes active or the problem area is isolated.
5. In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question/causing the intermittent condition.
  Are any ACTIVE DTCs present?
  
  Yes
  - Perform the appropriate diagnostic procedure. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Diagnosis and Testing .
  No
  - No problem found at this time. Perform the OCCUPANT CLASSIFICATION MODULE (OCM) SYSTEM VERIFICATION TEST . Erase all codes before returning vehicle to customer. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Standard Procedure .