LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2025 >> Traverse RS, 4WD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission - 8T65 (MF8) - Specifications >> Specifications >> Fastener Specifications

Fastener Specifications

GM6419113Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
1-Reverse and 1-2-3-4-5-6 Clutch Piston Housing Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 1-2-3-4-5-6 Clutch Backing Plate Retaining Ring Yes - - 1-Reverse and 1-2-3-4-5-6 Clutch Piston Housing Assemble
2 1-2-3-4-5-6 Clutch Piston Inner Seal Yes - -
3 1-2-3-4-5-6 Clutch Piston Seal Yes - -
GM6419115Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
5-7-Reverse and 6-7-8-9 Clutch Housing

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 5-7-Reverse Clutch Piston Inner Seal-Reluctor Wheel Yes - - 5-7-Reverse and 6-7-8-9 Clutch Housing Assemble
2 5-7-Reverse Clutch Piston Inner Seal Yes - -
3 5-7-Reverse Clutch Piston Dam Seal Yes - -
4 6-7-8-9 Clutch Piston Inner Seal Yes - -
5 6-7-8-9 Clutch Piston Outer Seal Yes - -
6 6-7-8-9 Clutch Dam Seal Yes - -
7 6-7-8-9 Clutch Dam Retaining Ring Yes - -
GM6596457Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Automatic Transmission Wiring Harness

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Automatic Transmission Wiring Harness Bolt [2x] - - 8 N.m (71 lb in) Control Valve Body Assembly Installation
GM6419121Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Auxiliary Fluid Accumulator

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Automatic Transmission Auxiliary Fluid Accumulator Bolt [3x] - - 22 N.m (16 lb ft) Auxiliary Fluid Accumulator Installation
2 Automatic Transmission Case Seal [2x] Yes - -
3 Accumulator Bypass Valve Seal Yes - -
4 Accumulator Bypass Valve Seal - Solenoid Yes - -
5 Accumulator Valve Body Bolt [2x] - - 2.7 N.m (24 lb in)
GM6419122Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Case and Associated Parts

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Control Valve Body Cover Stud [6x] - - Cover Bolt Torque Sequence  Control Valve Body Cover Installation
2 Control Valve Body Cover Gasket - - -
3 Control Valve Body Bolt [8x] - - Control Valve Body Bolt Torque Sequence (1 Of 2) Control Valve Body Bolt Torque Sequence (2 Of 2)  Control Valve Body Assembly Installation
4 Control Valve Body Bolt [12x] - - Control Valve Body Bolt Torque Sequence (1 Of 2) Control Valve Body Bolt Torque Sequence (2 Of 2)  Control Valve Body Assembly Installation
5 Control Valve Body Bolt [3x] - - Control Valve Body Bolt Torque Sequence (1 Of 2) Control Valve Body Bolt Torque Sequence (2 Of 2) 
6 Fluid Transfer Pipe Bolt - - 9 N.m (80 lb in) Control Valve Body Assembly Installation
7 Torque Converter Housing Gasket Yes - - Torque Converter Housing with Fluid Pump Assembly Installation
8 Automatic Transmission Fluid Pump Seal Yes - -
9 Torque Converter and Differential Housing Bolt [14x] - - Torque Converter and Differential Housing Bolt Torque Sequence 
10 Fluid Transfer Pipe Seal Yes - - Control Valve Body Assembly Installation
11 Control Valve Body Bolt [5x] - - Control Valve Body Bolt Torque Sequence (1 Of 2) Control Valve Body Bolt Torque Sequence (2 Of 2) 
12 Control Valve Solenoid Body Bolt - - 9 N.m (80 lb in)
13 Control Valve Body Cover Bolt [6x] - - Cover Bolt Torque Sequence  Control Valve Body Cover Installation
14 Automatic Transmission Fluid Temperature Sensor Seal Yes - - Control Valve Body Assembly Removal
GM6419127Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Control Valve Body Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Control Valve Solenoid Body Bolt [2x] - - 9 N.m (80 lb in) Control Valve Body Assembly Assemble
2 Control Valve Solenoid Body Bolt [2x] - - 9 N.m (80 lb in)
3 Control Valve Body Spacer Plate Retainer [2x] Yes - - Control Valve Body Assembly Assemble
GM6419128Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Control Valve Solenoid Body Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Control Valve Solenoid Body Bolt [2x] - - 8 N.m (71 lb in) Control Valve Body Assembly Installation
2 Control Valve Solenoid Body Bolt - - 9 N.m (80 lb in) Control Valve Body Assembly Assemble
GM6596045Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Engine Wiring Harness Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Engine Wiring Harness Clip Bracket Bolt - - 22 N.m (16 lb ft) Transmission Replacement (FWD)Transmission Replacement (AWD)
GM6612463Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Engine Wiring Harness Clip Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Engine Wiring Harness Clip Bracket Bolt - - 22 N.m (16 lb ft) Automatic Transmission Removal and Installation (FWD)Automatic Transmission Removal and Installation (AWD)
GM6577388Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Engine Wiring Harness Bracket Nuts

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Engine Wiring Harness Bracket Nut [2x] - - 9 N.m (80 lb in) Control Valve Body Cover Replacement
GM6419178Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Oil Pump Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Auxiliary Control Valve Body Spacer Plate Yes - - Transmission Fluid Pump, Front Differential Carrier Baffle, and Front Differential Ring Gear Installation
2 Torque Converter Fluid Seal Ring Yes - - Transmission Fluid Pump Assemble
3 Stator Shaft Seal Yes - -
4 Automatic Transmission Fluid Pump Seal Yes - -
5 Automatic Transmission Fluid Pump Gasket Yes - -
6 Automatic Transmission Fluid Pump Cover Bolt [5x] Yes - 9 N.m (80 lb in)
7 Automatic Transmission Fluid Pump Shaft Seal Yes - -
GM6419180Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Overdrive Carrier and Turbine Shaft

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Overdrive and Reaction Carrier Bolt [3x] Yes - 9 N.m (80 lb in) Overdrive and Reaction with Input Internal Gear Carrier Overhaul
2 Turbine Shaft Seal - - - 5-7-Reverse and 6-7-8-9 Clutch Housing Assemble
3 Turbine Shaft Retainer Ring Yes - -
GM6419181Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Park System Components

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Park Pawl Actuator Guide Pin Yes - - Park Release Lever and Park Pawl Actuator Installation
2 Manual Shift Shaft Seal Yes - - Manual Shift Shaft Seal Installation
3 Manual Shaft Detent Lever Hub Pin Yes - - Park Release Lever and Park Pawl Actuator Installation
4 Automatic Transmission Output Speed Sensor Bolt - - 9 N.m (80 lb in) Input and Output Speed Sensor Installation
GM5053382Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Torque Converter Bolt

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Transmission Torque Converter Bolt [6x] - Yes 60 N.m (44 lb ft) Automatic Transmission Removal and Installation (FWD)Automatic Transmission Removal and Installation (AWD)
GM6419188Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Torque Converter and Differential Housing Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Automatic Transmission Fluid Pump Cover Bolt [22x] - - Automatic Transmission Fluid Pump Cover Bolt Torque Sequence - Front  Transmission Fluid Pump, Front Differential Carrier Baffle, and Front Differential Ring Gear Installation
2 Automatic Transmission Fluid Pump Cover Bolt [19x] Yes - Automatic Transmission Fluid Pump Cover Bolt Torque Sequence - Back 
3 Torque Converter Fluid Seal Yes - - Torque Converter Fluid Seal Replacement (AWD)Torque Converter Fluid Seal Replacement (FWD)
4 Front Wheel Drive Shaft Oil Seal Yes - - Front Wheel Drive Shaft Oil Seal Replacement - Right Side (FWD)
5 Front Differential Carrier Baffle Bolt [2x] - - 9 N.m (80 lb in) Transmission Fluid Pump, Front Differential Carrier Baffle, and Front Differential Ring Gear Installation
6 Automatic Transmission Fluid Filter Yes - - Transmission Fluid Pump Assemble
7 Automatic Transmission Fluid Filter Seal Yes - -
GM6608690Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Bolt

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Transmission Bolt [7x] - - 58 N.m (43 lb ft) Automatic Transmission Removal and Installation (FWD)Automatic Transmission Removal and Installation (AWD)
GM6419597Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Bracket and Mount - Rear

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Transmission Rear Mount Bracket Bolt [3x] Yes - First Pass:
100 N.m (74 lb ft)
Final Pass: 45-60 degrees		 Transmission Rear Mount Bracket Replacement (AWD)Transmission Rear Mount Bracket Replacement (FWD)
2 Rear Transmission Mount Through Bolt - - 100 N.m (74 lb ft) Transmission Rear Mount Replacement (AWD)Transmission Rear Mount Replacement (FWD)
3 Rear Transmission Mount Bolt [2x] Yes - First Pass:
100 N.m (74 lb ft)
Final Pass: 90 to 105 degrees
GM6419190Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Case Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Input Shaft Support Bolt [3x] - - 12 N.m (106 lb in) Input Shaft Support Overhaul
2 5-7-Reverse and 6-7-8-9 Clutch Fluid Seal Ring [3x] Yes - -
3 Automatic Transmission Fluid Filter Bolt [3x] - - 10 N.m (89 lb in) Transmission Fluid Filter Assembly Installation
4 Automatic Transmission Fluid Filter Seal Yes - -
5 Automatic Transmission Fluid Filter Yes - -
6 Front Differential Carrier Baffle Bolt [2x] - - 12 N.m (106 lb in) Drive and Driven Sprocket, Drive Link, and Park Pawl Installation
7 Automatic Transmission Fluid Pressure Test Hole Plug - Yes 12 N.m (106 lb in) Automatic Transmission Fluid Pressure Test Hole Plug Replacement
8 Automatic Transmission Case Hole Plug - Yes 12 N.m (106 lb in) Automatic Transmission Case Hole Plug Replacement (Auxiliary Fluid Fill Plug)Automatic Transmission Case Hole Plug Replacement (Line Pressure Plug)
9 Automatic Transmission Fluid Level Hole Plug - Yes 12 N.m (106 lb in) Automatic Transmission Fluid Level Hole Plug Replacement
10 Automatic Transmission Fluid Pan Drain Plug - Yes 12 N.m (106 lb in) Automatic Transmission Fluid Pan Drain Plug Replacement
11 Front Wheel Drive Shaft Oil Seal Yes - - Front Wheel Drive Shaft Oil Seal Replacement - Left Side
12 Automatic Transmission Case Hole Plug - Yes 40 N.m (30 lb ft) Automatic Transmission Case Hole Plug Replacement (Auxiliary Fluid Fill Plug)Automatic Transmission Case Hole Plug Replacement (Line Pressure Plug)
13 Automatic Transmission Input Speed Sensor Bolt - - 9 N.m (80 lb in) Automatic Transmission Input Speed Sensor Replacement
14 Automatic Transmission Input Speed Sensor Seal - - -
15 Clutch Fluid Passage Seal [4x] Yes - - Control Valve Body Assembly Installation
GM6419598Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Mount

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Transmission Mount Transmission Side Bolt [4x] - - Transmission Mount Torque Sequence  Transmission Mount Replacement
2 Transmission Mount Brace Bolt [2x] - - 22 N.m (16 lb ft)
3 Transmission Mount Bolt [2x] - - 58 N.m (43 lb ft)
GM6419600Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Transmission Mount - Front

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Transmission Front Mount Bolt [2x] - - 58 N.m (43 lb ft) Transmission Front Mount Replacement
2 Transmission Front Mount Bolt - - 58 N.m (43 lb ft)
3 Transmission Front Mount Bolt - - 100 N.m (74 lb ft)
scientia non olet · About LEMON Manuals