LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2024 >> Traverse LS, 4WD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls And Fuel - 2.5L (LK0) - Repair Instructions >> Repair Instructions >> Fuel Tank Shield Replacement (F48) >> Installation Procedure

Installation Procedure

  1. GM4294857Courtesy of GENERAL MOTORS COMPANY

    Fuel Tank Shield (2) - Install

    2. CAUTION:

    Refer to Fastener Caution .

  2. Fuel Tank Heat Shield Retainer (1) - Install [2x]
  3. GM4294854Courtesy of GENERAL MOTORS COMPANY

    Fuel Tank Front Shield (2) - Install

  4. Fuel Tank Heat Shield Retainer (1) - Install [2x]
  5. GM5214679Courtesy of GENERAL MOTORS COMPANY

    Place a suitable adjustable jack under the fuel tank.

  6. Fuel Tank (1) - Install
  7. GM5214678Courtesy of GENERAL MOTORS COMPANY

    Fuel Tank Strap (2) - Install [2x]

  8. Fuel Tank Strap Bolt (1) - Install and tighten [4x] - Fastener Specifications
  9. Remove the adjustable jack from under the fuel tank.
  10. Connect the hose and wiring harness retainers as necessary.
  11. GM6594701Courtesy of GENERAL MOTORS COMPANY

    Evaporative Emission Canister Vent Hose (2) - Connect - Plastic Collar Quick Connect Fitting Service 

  12. Fuel Pump Fuel Feed Hose (1) - Connect - Plastic Collar Quick Connect Fitting Service 
  13. GM5214676Courtesy of GENERAL MOTORS COMPANY

    Evaporative Emission Canister Vent Hose (4) - Connect - Plastic Collar Quick Connect Fitting Service 

  14. Fuel Tank Filler Hose (3) - Install
  15. Fuel Tank Filler Hose Clamp (2) - Tighten - Fastener Specifications
  16. Wiring Harness (1) - Connect
  17. GM6465201Courtesy of GENERAL MOTORS COMPANY

    Rear Wheel Drive Differential Carrier Housing Gasket (2) - Install NEW

  18. Driveline Torque Tube (1) @ Differential Carrier Assembly - Install
  19. Using a suitable jack stand support the driveline torque tube.
  20. GM6466037Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    The driveline torque tube and differential carrier are balanced as an assembly. When re-using the original driveline torque tube it should be re-installed in the same position in relation the pinion splines.

    Ensure the driveline torque tube and pinion spline marks (1) are aligned.

  21. GM6465203Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    Refer to Fastener Caution .

    If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:

    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the bolts. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  22. Driveline Torque Tube Bolt (1) - Install and tighten [6x] - Fastener Specifications
  23. GM6465202Courtesy of GENERAL MOTORS COMPANY

    Differential Carrier Front Bolt (1) - Install and tighten - Fastener Specifications

  24. Remove the jack stand from under the differential carrier.
  25. Install the propeller shaft. Two-Piece Propeller Shaft Replacement
  26. Remove the support and lower the vehicle.
  27. Refill the fuel tank.
  28. Inspect for fuel leaks.
scientia non olet · About LEMON Manuals