Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Approximate Fluid Capacities | |||
| Torque | Fastener Specifications | |||
| Wheel Drive Shaft Nut | ||||
| Front or Rear | First Pass: 244 lb ft (330 N.m) Second Pass: Loosen 45 degrees Final Pass: 199 lb ft (270 N.m) |
|||
| Battery | Battery Electrical Drain/Parasitic Load Test | |||
| Brakes | ||||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT Hydraulic Brake System Bleeding (Manual) or Hydraulic Brake System Bleeding (Pressure) |
|||
| Disc Brakes | ||||
| Service Specifications | Disc Brake Component Specifications | |||
| Torque | Fastener Specifications | |||
| Charging | ||||
| Generator | Charging System Test | |||
| Torque | Fastener Specifications | |||
| Drive Belts | ||||
| Adjustment | Non-Adjustable Serpentine Belt | |||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under Drive Belt Replacement |
|||
| Engine Cooling | ||||
| General Service Specifications | Specifications | |||
| Radiator Cap Pressure | Pressure Cap Testing | |||
| Thermostat R & I | Engine Coolant Thermostat Housing Replacement | |||
| Water Pump R & I | Water Pump Replacement | |||
| Engine Mechanical | ||||
| Compression | Engine Compression Test | |||
| Oil Pressure | Minimum @ Idle: 69 kPa (10 psi) Minimum @ 2000 RPM: 138 kPa (20 psi) |
|||
| Overhaul | Engine Mechanical Specifications | |||
| Torque | Fastener Specifications | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flex Plate Torque | First Pass: 30 N.m (22 lb. ft.) Final Pass: Tighten 45° |
|||
| Fuel System | ||||
| Pressure Specification | Ignition ON, Engine OFF - 345-650 kPa (50-94 psi) Engine at IDLE - 300-400 kPa (43-58 psi) |
|||
| Fuel Pressure Test Procedure | Circuit/System Verification | |||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | |||
| Fuel Filter R & I | Fuel Tank Fuel Pump Module Replacement (FWD) or Fuel Tank Fuel Pump Module Replacement (AWD) | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | |||
| Ignition Wires (Routing) | Coil On Plug | |||
| Spark Plug - For application, see parts catalog | ||||
| Gap | 0.95-1.10 mm (0.0375-0.0433 in) | |||
| Torque | 13 lb ft (18 N.m) | |||
| Starting | ||||
| Starter | Starter Replacement | |||
| Torque | Fastener Specifications | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Wheel Alignment Specifications | |||
| Torque | Fastener Specifications | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) For Lug Nut Tightening Sequence, Please See the Figure Under Installation Procedure |
|||