LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Traverse Premier, FWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Driver Assistance Systems >> Diagnostic Information and Procedures >> Forward Collision Alert System Malfunction (except UGN) >> Circuit/System Testing

Circuit/System Testing

Test 1

  1. Ignition - On / Vehicle - In Service Mode
  2. Disconnect the electrical connector: X3 @ K9 Body Control Module
  3. Test for less than 1 V between the test points:
    • Ignition circuit terminal 4 & Ground
    • Signal circuit terminal 16 & Ground
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  4. Ignition/Vehicle & All vehicle systems - Off
  5. Test for infinite resistance between the test points:
    • Ignition circuit terminal 4 & Ground
    • Signal circuit terminal 16 & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  6. Operate the component: Forward Collision Alert Switch - Press and hold the switch

    Test for 2.0 k to 3.0 kohms between the test points: Ignition circuit terminal 4 & Signal circuit terminal 16

    • If not between 2.0 k and 3.0 kohms 
    1. Disconnect the electrical connector: S70C Steering Wheel Controls Switch - Left Upper
    2. Test for less than 2 ohms between the test points: Ignition circuit terminal 4 @ K9 Body Control Module & Ignition circuit terminal 8 @ S70L Steering Wheel Controls Switch - Left
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • Go to next step: If less than 2 ohms
    3. Test for less than 2 ohms between the test points: Signal circuit terminal 16 @ K9 Body Control Module & Signal circuit terminal 9 @ S70L Steering Wheel Controls Switch - Left
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • Go to next step: If less than 2 ohms
    4. Replace the component: S70L Steering Wheel Controls Switch - Left
    • Go to next step: If between 3.5 k and 3.8 kohms 
  7. Test for 6.6 k to 7.6 kohms between the test points: Ignition circuit terminal 4 & Signal circuit terminal 16
    • If not between 6.6 k and 7.6 kohms 

      Replace the component: S70L Steering Wheel Controls Switch - Left

    • Go to next step: If between 6.6 k and 7.6 kohms 
  8. Replace the component: K9 Body Control Module

Test 2

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: P43 Collision Alert Indicators
  3. Verify a test lamp turns On between the test points: Ground circuit terminal 4 & B+
    • If the test lamp does not turn On 
    1. Test for less than 2 ohms between the test points: Ground circuit terminal 4 & Ground terminal
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If the test lamp turns On 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify a test lamp turns On between the test points: Ignition circuit terminal 1 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for less than 2 ohms between the test points: Ignition circuit terminal 1 @ P43 Collision Alert Indicators & The other end of the circuit
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for infinite resistance between the test points: Ignition circuit terminal 1 & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Test or replace the component: P43 Collision Alert Indicators
    • Go to next step: If the test lamp turns On 
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: P16 Instrument Cluster
  8. Ignition - On / Vehicle - In Service Mode
  9. Test for less than 1 V between the test points:
    • Control circuit terminal 30 @ P16 Instrument Cluster & Ground
    • Control circuit terminal 12 @ P16 Instrument Cluster & Ground
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  10. Ignition/Vehicle - Off
  11. Test for infinite resistance between the test points:
    • Control circuit terminal 30 @ P16 Instrument Cluster & Ground
    • Control circuit terminal 12 @ P16 Instrument Cluster & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  12. Test for less than 2 ohms between the test points:
    • Control circuit terminal 30 @ P16 Instrument Cluster & Control circuit terminal 3 @ P43 Collision Alert Indicators
    • Control circuit terminal 12 @ P16 Instrument Cluster & Control circuit terminal 2 @ P43 Collision Alert Indicators
    • If 2 ohms or greater 

      Repair the open/high resistance in the circuit.

    • Go to next step: If less than 2 ohms 
  13. Replace the component: P43 Collision Alert Indicators
  14. Ignition - On / Vehicle - In Service Mode
  15. Perform the appropriate scan tool control function: All Indicators

    Verify the component activates: Collision Alert - Indicators

    • If the component does not work as specified 

      Replace the component: P16 Instrument Cluster

    • Go to next step: If the component works as specified 
  16. All OK.
scientia non olet · About LEMON Manuals