LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Suburban Z71 >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> Driver Assistance Systems >> Repair Instructions >> Image Processing Module Replacement >> Removal Procedure

Removal Procedure

WARNING:

Refer to SIR Warning .

WARNING:

Refer to SIR Inflator Module Handling and Storage Warning .

CAUTION:

Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

  1. 3rd Row Seat (2) - Remove - 3rd Row Seat Removal and Installation
    GM5598917Courtesy of GENERAL MOTORS COMPANY
  2. Disable the SIR system. SIR Disabling and Enabling
  3. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5591920Courtesy of GENERAL MOTORS COMPANY
  4. Rear Side Door Sill Garnish Molding (1) - Remove
  5. Place the rear seat (1) in the fold and tumble position.
    GM5607687Courtesy of GENERAL MOTORS COMPANY
  6. Liftgate Weatherstrip (1) - Reposition
    GM5577842Courtesy of GENERAL MOTORS COMPANY
  7. Liftgate Lock Striker Cover (1) - Remove
    GM5577843Courtesy of GENERAL MOTORS COMPANY
  8. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5577844Courtesy of GENERAL MOTORS COMPANY
  9. Rear End Trim Finish Panel (1) - Remove
  10. Rear Seat Belt Retractor Sleeve (1) - Reposition
    GM5591921Courtesy of GENERAL MOTORS COMPANY
  11. Rear Seat Belt Anchor Plate Bolt (2) - Remove
  12. Quarter Window Trim Finish Panel Bolt Cap (1) - Remove
    GM5591923Courtesy of GENERAL MOTORS COMPANY
  13. Quarter Window Trim Finish Panel Bolt (2) - Reposition
  14. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5591925Courtesy of GENERAL MOTORS COMPANY
  15. Body Lock Pillar Upper Trim Panel (1) - Reposition
  16. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5591927Courtesy of GENERAL MOTORS COMPANY
  17. Body Side Rear Window Garnish Molding (1) - Reposition
  18. Body Rear Corner Upper Garnish Molding Bolt (1) - Remove
    GM5591929Courtesy of GENERAL MOTORS COMPANY
  19. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5591930Courtesy of GENERAL MOTORS COMPANY
  20. Body Rear Corner Upper Garnish Molding (1) - Reposition
  21. 3rd Row Seat Belt Retractor Bolt- Lower (1) - Remove
    GM5605055Courtesy of GENERAL MOTORS COMPANY
  22. Convenience Net Retainer (1) - Remove
    GM5605064Courtesy of GENERAL MOTORS COMPANY
  23. Cargo Tie Down Loop Bolt Cap (2) - Open
  24. Cargo Tie Down Loop Bolt (3) - Remove
  25. Cargo Tie Down Loop (4) - Remove
  26. Using a flat-bladed plastic trim tool, release the retaining clips.
    GM5605067Courtesy of GENERAL MOTORS COMPANY
  27. Quarter Lower Rear Trim Panel (1) - Reposition
  28. Remove the wiring harness retainers, as needed.
  29. Disconnect the electrical connectors.
    GM5581893Courtesy of GENERAL MOTORS COMPANY
  30. Active Safety Control Module Bracket Nut (1) - Remove [2x]
  31. Active Safety Control Module Bracket (2) - Remove
  32. Remove the wiring harness retainers
  33. Release the retaining tab.
    GM5581886Courtesy of GENERAL MOTORS COMPANY
  34. Image Processing Module (1) - Remove
scientia non olet · About LEMON Manuals