Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Drive Shaft Nut | First Pass: 150 N.m (111 lb ft) Second Pass: Release 45 degrees Final Pass: 250 N.m (199 lb ft) |
||
| Battery | BATTERY ELECTRICAL DRAIN/PARASITIC LOAD TEST | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT FRONT, LEFT REAR, RIGHT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) , or HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | CHARGING SYSTEM TEST | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the figure under 1.5L WATER PUMP, AIR CONDITIONING COMPRESSOR, AND GENERATOR BELT REPLACEMENT See the figure under 2.0L DRIVE BELT REPLACEMENT |
||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | PRESSURE CAP TESTING | ||
| Thermostat R & I | |||
| 1.5L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LFV) | ||
| 2.0L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LTG) | ||
| Water Pump R & I | |||
| 1.5L | WATER PUMP REPLACEMENT (LFV) | ||
| 2.0L | WATER PUMP REPLACEMENT (LTG) | ||
| Engine Mechanical | |||
| 1.5L (LFV) | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | @ 1500 RPM 100° C: 29-36 psi 200-250 kPa | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| 2.0L (LTG) | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | @ 700 RPM 100° C: 20-29 psi 140-200 kPa | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 1.5L | First Pass - 20 N.m (15 lb ft) Second Pass - 30 N.m (22 lb ft) Final Pass - additional 70 degrees |
||
| 2.0L | First Pass - 30 N.m (22 lb ft) Final Pass - additional 40 degrees |
||
| Fuel System | |||
| Pressure Specification | Ignition ON, Scan Tool Commanded - 345-650 kPa (50-94 PSI) | ||
| Fuel Pressure Test Procedure | 1.5L CIRCUIT/SYSTEM VERIFICATION 2.0L CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | 1.5L FUEL PUMP REPLACEMENT 2.0L FUEL TANK FUEL PUMP MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| See Parts Catalog for Application | |||
| Gap | 1.5L - 0.60-0.70 mm (0.024-0.028 in) 2.0L - 0.95-1.10 mm (0.037-0.043 in) |
||
| Torque | 1.5L - 17 N.m (13 lb ft) 2.0L - 20 N.m (15 lb ft) |
||
| Starting | |||
| Starter | STARTER REPLACEMENT (LFV) 1.5L , or STARTER REPLACEMENT (LTG) 2.0L | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) For Tightening Sequence, see the figure under INSTALLATION PROCEDURE |
||