LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2018 >> Traverse L >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Memory Modules >> Secondary And Configurable Customer Control System >> Diagnostic Information and Procedures >> Drive Mode Switch Malfunction >> Circuit/System Testing

Circuit/System Testing

Test 1

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: S126 Drive Mode Select Switch
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 5 & Ground
    • If 10 ohms or greater 
    1. Test for less than 2 ohms between the test points: Ground circuit terminal @ Component harness & Ground terminal
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On/Vehicle - In Service Mode
  5. Test for 4.8 to 5.2 V between the test points: 5 V Reference circuit terminal 9 & Ground
    • If less than 4.8 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: 5 V Reference circuit terminal @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 ohms between the test points: 5 V Reference circuit terminal @ Component harness & The other end of the circuit @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K20 Engine Control Module
    • If greater than 5.2 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: 5 V Reference circuit terminal @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If between 4.8 and 5.2 V 
  6. Test for less than 1 V between the test points: Signal circuit terminal 7 & Ground
    • If 1 V or greater 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If less than 1 V 
  7. Ignition/Vehicle & All vehicle systems - Off
  8. Disconnect the electrical connector: K20 Engine Control Module
  9. Test for infinite resistance between the test points: Signal circuit terminal 7 @ Component harness & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  10. Test for less than 2 ohms between the test points: Signal circuit terminal 7 @ Component harness & The other end of the circuit @ Control module harness
    • If less than infinite resistance 

      Repair the open/high resistance in the circuit.

    • Go to next step: If infinite resistance 
  11. Test or replace the component: S126 Drive Mode Select Switch
  12. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

    Verify the DTC does not set.

    • If the DTC sets 

      Replace the component: K20 Engine Control Module

    • Go to next step: If the DTC is not set 
  13. All OK.

Test 2

  1. Ignition - On/Vehicle - In Service Mode
  2. Headlamp Switch = On
  3. Verify a test lamp turns On between the test points: Control circuit terminal 8 & Ground
    • Go to next step: If the test lamp turns On 
  4. Ignition/Vehicle - Off & Remove - Test lamp
  5. Connect the electrical connector: S126 Drive Mode Select Switch
  6. Disconnect the electrical connector: X2 & X5 @ K9 Body Control Module
  7. Ignition - On/Vehicle - In Service Mode
  8. Test for less than 1 V between the test points:
    • Signal circuit terminal 10 X5 & Ground
    • Signal circuit terminal 21 X5 & Ground
    • {With V92} Signal circuit terminal 23 X5 & Ground
    • {With F48} Signal circuit terminal 6 X2 & Ground
    • If 1 V or greater 
    1. Disconnect the electrical connector: S126 Drive Mode Select Switch
    2. Test for less than 1 V between the test points:
      • Signal circuit terminal 10 X5 & Ground
      • Signal circuit terminal 21 X5 & Ground
      • {With V92} Signal circuit terminal 23 X5 & Ground
      • {With F48} Signal circuit terminal 6 X2 & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: S126 Drive Mode Select Switch
    • Go to next step: If less than 1 V 
  9. Ignition/Vehicle - Off
  10. Test for infinite resistance between the test points:
    • Signal circuit terminal 10 X5 & Ground
    • Signal circuit terminal 21 X5 & Ground
    • {With V92} Signal circuit terminal 23 X5 & Ground
    • {With F48} Signal circuit terminal 6 X2 & Ground
    • If less than infinite resistance 
    1. Disconnect the electrical connector: S126 Drive Mode Select Switch
    2. Test for infinite resistance between the test points:
      • Signal circuit terminal 10 X5 & Ground
      • Signal circuit terminal 21 X5 & Ground
      • {With V92} Signal circuit terminal 23 X5 & Ground
      • {With F48} Signal circuit terminal 6 X2 & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: S126 Drive Mode Select Switch
    • Go to next step: If infinite resistance 
  11. Connect a 3 A fused jumper wire between each of the following circuit pairs, one at a time:
    • Signal circuit terminal 10 X5 & Ground
    • Signal circuit terminal 21 X5 & Ground
    • {With V92} Signal circuit terminal 23 X5 & Ground
    • {With F48} Signal circuit terminal 6 X2 & Ground
  12. Verify the component works as specified: Drive Mode - LED (Light Emitting Diode) @ S126 Drive Mode Select Switch = On
    • If the component does not work as specified 
    1. Disconnect the electrical connector: S48E Multifunction Switch - Center Console
    2. Ignition/Vehicle - Off
    3. Test for less than 2 ohms between the test points:
      • Signal circuit terminal 10 X5 & Ground
      • Signal circuit terminal 21 X5 & Ground
      • {With V92} Signal circuit terminal 23 X5 & Ground
      • {With F48} Signal circuit terminal 6 X2 & Ground
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: S48E Multifunction Switch - Center Console
    • Go to next step: If the component works as specified 
  13. Replace the component: K9 Body Control Module
scientia non olet · About LEMON Manuals