Common Specs & Procedures Index
(SPARK) COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities (R-134a) , or Approximate Fluid Capacities (R-1234yf) | ||
| Torque | Fastener Specifications Automatic: Fastener Specifications Manual: Fastener Specifications |
||
| Front Wheel Drive Shaft Nut | |||
| Torque: First Pass |
50 Nm, (37 lb ft) |
||
| Second Pass | 60 degrees | ||
| Rear Wheel Hub to Rear Axle Bolts | |||
| Torque: | 58 Nm, (43 lb ft) | ||
| Battery | Fastener Specifications , Battery Description and Operation | ||
| Brakes | |||
| Bleeding Sequence | Hydraulic Brake System Bleeding (Manual) Hydraulic Brake System Bleeding (Pressure) |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Drum Brakes | |||
| Service Specifications | Drum Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Generator Replacement | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See routing illustration under Drive Belt Replacement | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 1.4L | Engine Coolant Thermostat Housing Replacement (LV7) , or Engine Coolant Thermostat Housing Replacement (L5Q) | ||
| Water Pump R & I | |||
| 1.4L | Water Pump Replacement (LV7) , or Water Pump Replacement (L5Q) | ||
| Engine Mechanical | |||
| 1.4L | |||
| Compression Ratio: | 10.5:1 Engine Compression Test |
||
| Oil Pressure - @ 1500 RPM 100°C | 200-250 kPa (29-36 psi) | ||
| Overhaul | Engine Mechanical Specifications (LV7) , or Engine Mechanical Specifications (L5Q) | ||
| Torque | Fastener Specifications (LV7) , or Fastener Specifications (L5Q) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque (Use NEW Fasteners) | |||
| First Pass | 30 N.m (22 lb ft) | ||
| Final Pass | An Additional 70 Degrees | ||
| Fuel System | |||
| Pressure Specification (Commanded with Scan Tool) | 345-650 kPa (50-94 psi) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | In the fuel tank | ||
| Fuel Filter R & I | Fuel Tank Fuel Pump Module Replacement (32L (8.5 US Gallon) Tank) Fuel Tank Replacement (35L (9 US Gallon) Tank) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | See info & graphic for 4 cylinder engine under: FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | |||
| 1.4L | Coil On Plug | ||
| Spark Plug | |||
| 1.4L (Type = Refer to Electronic Parts Catalog) | |||
| Gap Gap |
0.80-0.90 mm (0.0315-0.0354 in)Engine Mechanical Specifications (LV7) 0.60-0.70 mm (0.024 - 0.028 in) Engine Mechanical Specifications (L5Q) |
||
| Torque | 17 N.m, (13 lb ft) | ||
| Starting | |||
| Starter | Starter Replacement (without Start/Stop) Starter Replacement (LV7) |
||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft). See tightening sequence illustration under: Installation Procedure | ||