LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> Traverse LS Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Headlights >> Lighting System - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> DTC B2530: Front Fog Lamp Control Circuit >> Circuit/System Testing

Circuit/System Testing

DTC B2530 (Z88 with T96 without TVD)

  1. Ignition OFF, disconnect the KR46 Front Fog Lamp Relay, ignition ON
  2. Test for less than 10 Ω between the ground circuit terminal 85 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify a test lamp illuminates between the B+ circuit terminal 87 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood.

    • If the test lamp illuminates 
  4. Connect a test lamp between the control circuit terminal 86 and B+, ignition ON.
  5. Verify the test lamp turns ON and OFF when commanding the Fog Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit terminal and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  6. Test or replace the KR46 Front Fog Lamp Relay.

DTC B2530 (T96)

  1. Ignition OFF, disconnect the KR46 Front Fog Lamp Relay, ignition ON
  2. Verify a test lamp illuminates between the B+ circuit terminal 85 and ground.
    • If the test lamp does not illuminate 

      Replace the X51A Fuse Block - Instrument Panel.

    • If the test lamp illuminates 
  3. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
    • If the test lamp does not illuminate 

      Replace the X51A Fuse Block - Instrument Panel.

    • If the test lamp illuminates 
  4. Connect a test lamp between the control circuit terminal 86 and B+, ignition ON.
  5. Verify the test lamp turns ON and OFF when commanding the Fog Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit terminal and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  6. Test or replace the KR46 Front Fog Lamp Relay.

DTC B2530 (Z88 with TVD and T96)

  1. Ignition OFF, disconnect the KR46 Front Fog Lamp Relay, ignition ON
  2. Verify a test lamp illuminates between the B+ circuit terminal 86 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood.

    • If the test lamp illuminates 
  3. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood.

    • If the test lamp illuminates 
  4. Connect a test lamp between the control circuit terminal 85 and B+, ignition ON.
  5. Verify the test lamp turns ON and OFF when commanding the Fog Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit terminal and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  6. Test or replace the KR46 Front Fog Lamp Relay.
scientia non olet · About LEMON Manuals