Radio Controls Scan Tool Information
Radio Controls Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| Battery Voltage | Varies | The scan tool displays volts. This is the voltage at the input to the radio controls. |
| Power Mode | Run | The scan tool displays Off, Accessory, Run or Crank Request. This is the vehicle power mode status as received by the radio controls via serial data. |
| Driver Seat Heating/Venting/Cooling Level | Varies | The scan tools displays No LED Activated, 1 LED Activated, Seat Back and Cushion Heating, Seat Back Heating, 2 LEDs Activated, Seat Venting/Cooling, or 3 LEDs Activated. The scan tool displays the level at which the LEDs are illuminated on the driver heated seat indicator. |
| Passenger Seat Heating/Venting/Cooling Level | Varies | The scan tools displays No LED Activated, 1 LED Activated, Seat Back and Cushion Heating, Seat Back Heating, 2 LEDs Activated, Seat Venting/Cooling, or 3 LEDs Activated. The scan tool displays the level at which the LEDs are illuminated on the passenger heated seat indicator. |
| Driver Seat Heating/Venting/Cooling Mode | Varies | The scan tools displays Seat Back and Cushion Heating, Seat Back Heating, or Seat Venting/Cooling. The scan tool displays the driver seat heating or cooling mode that is currently active. |
| Passenger Seat Heating/Venting/Cooling Mode | Varies | The scan tools displays Seat Back and Cushion Heating, Seat Back Heating, or Seat Venting/Cooling. The scan tool displays the passenger seat heating or cooling mode that is currently active. |
| Key Stuck | No | The scan tool indicates Yes or No. This indicates if one of the secondary steering wheel controls buttons has been detected in a stuck/ always on state or held too long.. |
| Infotainment Controls | No Button Pressed | The scan tool displays No button Pressed, Button Pressed, or Multiple Buttons Pressed. The scan tool indicates if controls buttons are currently pressed. |
| Info Display/Infotainment Faceplate Wake-Up Command | Inactive | The scan tool displays Active or Inactive. This indicates if the wakeup input for the display/controls is active. |
| End Model Part Number | Varies | The scan tool displays the end model part number. |
| Boot Software Part Number | Varies | The scan tool displays the boot software ID number. |
| Manufacturer Enable Counter | 0 | The scan tool displays the counter value. This counter is used for manufacturing purposes only. |
| Calibration Part Number 1 | Varies | The scan tool displays the software module ID 1. |
| Calibration Part Number 2 | Varies | The scan tool displays the software module ID 2. |
| Calibration Part Number 3 | Varies | The scan tool displays the software module ID 3. |
| Calibration Part Number 4 | Varies | The scan tool displays the software module ID 4. |
| Calibration Part Number 5 | Varies | The scan tool displays the software module ID 5. |
| Calibration Part Number 6 | Varies | The scan tool displays the software module ID 6. |
| Calibration Part Number 7 | Varies | The scan tool displays the software module ID 7. |
| Calibration Part Number 8 | Varies | The scan tool displays the software module ID 8. |
| Calibration Part Number 9 | Varies | The scan tool displays the software module ID 9. |
| Calibration Part Number 10 | Varies | The scan tool displays the software module ID 10. |
| Calibration Part Number 11 | Varies | The scan tool displays the software module ID 11. |
| Calibration Part Number 12 | Varies | The scan tool displays the software module ID 12. |
| Calibration Part Number 13 | Varies | The scan tool displays the software module ID 13. |
| Calibration Part Number 14 | Varies | The scan tool displays the software module ID 14. |
| Calibration Part Number 15 | Varies | The scan tool displays the software module ID 15. |
| Calibration Part Number 16 | Varies | The scan tool displays the software module ID 16. |
| Diagnostic Data Identifier | Varies | Identifies a supplier and system specific data stream used by diagnostic testers to interpret a diagnostic data stream. |
Radio Controls Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Info Display/Infotainment Faceplate Reset | This output is a reset command to reset the display/controls assembly. |
| Backlight Dimming | This control function is used to increase or decrease the backlighting dimming level of the controls, expressed in percent. |
| Seat Heating/Venting/Cooling Indicator | This control function is used to turn the seat heating/venting/cooling indicator on or off. |
Radio Controls Configuration/Reset Options
| Scan Tool Output Control | Description |
|---|---|
| Info Display/Infotainment Faceplate Reset | This output is a reset command to reset the display/controls assembly. |
| CAN Bus Configuration Learn | Implementation of this device control allows the user to force the module to relearn all previously learned source IDs. |