LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> SS Automatic Trans >> Repair and Diagnosis (Single Page) >> Body & Frame >> Seats >> Power Seat System >> Diagnostic Information and Procedures >> DTC B1850: Driver Seat Lumbar Support Horizontal Position Sensor Circuit >> Circuit/System Testing

Circuit/System Testing

  1. Ignition OFF and all vehicle systems OFF, disconnect the X2 harness connector at the M53D Seat Lumbar Support Motor - Driver. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the low reference circuit terminal 3 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF, disconnect the X5 harness connector at the K40 Seat Memory Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K40 Seat Memory Control Module.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Test for 4.8 - 5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the X5 harness connector at the K40 Seat Memory Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K40 Seat Memory Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the X5 harness connector at the K40 Seat Memory Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K40 Seat Memory Control Module.
    • If between 4.8 - 5.2 V 
  5. Verify the scan tool Driver Seat Lumbar Support Horizontal Position is less than 1 V.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the X5 harness connector at the K40 Seat Memory Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K40 Seat Memory Control Module.
    • If less than 1 V 
  6. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the 5 V reference circuit terminal 1
  7. Verify the scan tool Driver Seat Lumbar Support Horizontal Position is greater than 4.65 V.
    • If 4.65 V or less 
    1. Ignition OFF, remove the jumper wire, disconnect the X5 harness connector at the K40 Seat Memory Control Module.
    2. Test for infinite resistance between the signal circuit terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K40 Seat Memory Control Module.
    • If greater than 4.65 V 
  8. Test or replace the M53D Seat Lumbar Support Motor - Driver.
scientia non olet · About LEMON Manuals