LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2014 >> Volt >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Mirror System >> Diagnostic Information and Procedures >> Power Mirror Malfunction >> Circuit/System Testing

Circuit/System Testing

Both Outside Rearview Mirrors Inoperative

  1. Vehicle OFF, disconnect the harness connector at the S52 Outside Rearview Mirror Switch. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 11 and ground.
    • If 10 Ω or greater 
    1. Vehicle OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify a test lamp illuminates between the B+ circuit terminal 12 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Vehicle OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Vehicle OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for infinite resistance between each of the control circuit terminals listed below and ground:
      • Control circuit terminal 5
      • Control circuit terminal 6
      • Control circuit terminal 7
      • Control circuit terminal 8
      • Control circuit terminal 9
      • Control circuit terminal 10
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S52 Outside Rearview Mirror Switch.
    • If the test lamp illuminates 
  4. Test or replace the S52 Outside Rearview Mirror Switch.

Driver Outside Mirror Movement Malfunction

  1. Vehicle OFF, disconnect the harness connector at the M77D Outside Rearview Mirror Motor-Driver. Vehicle in Service Mode
  2. Connect a test lamp between the control circuit terminal 2 and control circuit terminal 3.
  3. Verify the test lamp turns ON when commanding the UP and DOWN states with the S52 Outside Rearview Mirror Switch.
    • If the test lamp remains OFF during either of the commands 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch.
    2. Test for infinite resistance between each control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S52 Outside Rearview Mirror Switch.
    • If the test lamp is always ON 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch, Vehicle in Service Mode.
    2. Test for less than 1 V between each control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, test or replace the S52 Outside Rearview Mirror Switch
    • If the test lamp turns ON during each of the commands 
  4. Connect a test lamp between the control circuit terminal 1 and control circuit terminal 2.
  5. Verify the test lamp turns ON when commanding the LEFT and RIGHT states with the S52 Outside Rearview Mirror Switch.
    • If the test lamp remains OFF during either of the commands 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch.
    2. Test for infinite resistance between each control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S52 Outside Rearview Mirror Switch.
    • If the test lamp is always ON 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch, Vehicle in Service Mode.
    2. Test for less than 1 V between each control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, test or replace the S52 Outside Rearview Mirror Switch
    • If the test lamp turns ON during each of the commands 
  6. Test or replace the M77D Outside Rearview Mirror Motor-Driver.

Passenger Outside Mirror Movement Malfunction

  1. Vehicle OFF, disconnect the harness connector at the M77P Outside Rearview Mirror Motor-Passenger. Vehicle in Service Mode
  2. Connect a test lamp between the control circuit terminal 2 and control circuit terminal 3.
  3. Verify the test lamp turns ON when commanding the UP and DOWN states with the S52 Outside Rearview Mirror Switch.
    • If the test lamp remains OFF during either of the commands 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch.
    2. Test for infinite resistance between each control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S52 Outside Rearview Mirror Switch.
    • If the test lamp is always ON 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch, Vehicle in Service Mode.
    2. Test for less than 1 V between each control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, test or replace the S52 Outside Rearview Mirror Switch
    • If the test lamp turns ON during each of the commands 
  4. Connect a test lamp between the control circuit terminal 1 and control circuit terminal 2.
  5. Verify the test lamp turns ON when commanding the LEFT and RIGHT states with the S52 Outside Rearview Mirror Switch.
    • If the test lamp remains OFF during either of the commands 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch.
    2. Test for infinite resistance between each control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S52 Outside Rearview Mirror Switch.
    • If the test lamp is always ON 
    1. Vehicle OFF, remove the test lamp, disconnect the harness connector at the S52 Outside Rearview Mirror Switch, Vehicle in Service Mode.
    2. Test for less than 1 V between each control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, test or replace the S52 Outside Rearview Mirror Switch
    • If the test lamp turns ON during each of the commands 
  6. Test or replace the M77P Outside Rearview Mirror Motor-Passenger.
scientia non olet · About LEMON Manuals