Radio Scan Tool Information
Radio Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| Antenna Module | Enabled | The scan tool displays Enabled or Disabled. This indicates if the system uses an antenna module and the output status between the radio and the antenna module. |
| Auxiliary Audio Input | Not Present | The scan tool displays Present or Not Present. This parameter displays present when an auxiliary input is connected. |
| Battery Voltage | Varies | The scan tool displays volts. This is the voltage at the input to the radio. |
| Digital Radio Receiver | Present | The scan tool displays Present or Not Present. This is the state of the Digital Audio Broadcast. |
| Power Mode | Run | The scan tool displays Off, Accessory, Run or Crank Request. This is the current power mode of the radio. |
| Radio Signal Strength | Varies | This displays the signal strength in dB. This is the signal strength of the currently tuned radio station. |
| Theft Lock Armed | Learned VIN | The scan tool displays Learned VIN or No VIN. This is the state of the VIN programming in the radio. |
| Radio Theft Lock Status | Inactive | The scan tool displays Active or Inactive. This is the state of the theft lock system. Active indicates the radio is locked. Inactive indicates the theft lock system is armed and the radio is unlocked. |
| Test Bench Mode | Inactive | The scan tool displays Active or Inactive. This parameter indicates if the radio is in bench or user mode. |
| End Model Part Number | Varies | End Model Part Number is the part number for the hardware of the control module with software and calibrations. |
| Base Model Part Number | Varies | Base Model Part Number is the part number for the hardware without software and calibrations. |
| Boot Software Part Number | Varies | The scan tool displays the boot software ID number. |
| Calibration Part Number 1 | Varies | The scan tool displays the software module ID 1. |
| Calibration Part Number 2 | Varies | The scan tool displays the software module ID 2. |
| Calibration Part Number 3 | Varies | The scan tool displays the software module ID 3. |
| Calibration Part Number 4 | Varies | The scan tool displays the software module ID 4. |
| Calibration Part Number 5 | Varies | The scan tool displays the software module ID 5. |
| Calibration Part Number 6 | Varies | The scan tool displays the software module ID 6. |
| Calibration Part Number 7 | Varies | The scan tool displays the software module ID 7. |
| Calibration Part Number 8 | Varies | The scan tool displays the software module ID 8. |
| Calibration Part Number 9 | Varies | The scan tool displays the software module ID 9. |
| Calibration Part Number 10 | Varies | The scan tool displays the software module ID 10. |
| Digital Radio Receiver ID | Varies | The scan tool displays the Digital Audio Broadcast receiver ID. |
| Vin Digits 2-17 | Varies | The scan tool displays the learned VIN digits 2-17. |
| Subscriber ID | Varies | Identifies the alphanumeric dealer code or the tester's (Tech2, MDI etc.) serial number. This string is programmed into the ECU memory during the last programming event. |
| Module Diagnostic Address | 80 | Displays the 2 digit diagnostic address of the control module. |
| Date Programmed | Varies | Displays the date when the ECU was last programmed. |
Radio Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Left Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Left Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Eject | This output is a command to eject the disc. |