LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2013 >> Impala LS >> Repair and Diagnosis >> External Pages >> Different car >> Section 228 (Engine Control System - 5.3L - DTC P0016 To DTC P0135) >> DTC P0107 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Chevrolet Monte Carlo and 2006 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic table.

  1. 4:  Operate the vehicle within the same conditions as when the DTC failed. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records can help to locate an intermittent condition.
DTC P0107

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Control Module (ECM) Connector End Views or Engine Controls Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition, with the engine OFF.
  2. Monitor the Diagnostic Trouble Code (DTC) Information with the scan tool.
Is DTC P0641 also set?		 - Go to DTC P0641 Go to Step 3 
3 Observe the manifold absolute pressure (MAP) sensor parameter with the scan tool.
Is the voltage less than the specified value?		 0.1 V Go to Step 5  Go to Step 4 
4 
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 5  Go to Testing for Intermittent Conditions and Poor Connections
5
  1. Turn OFF the ignition.
  2. Disconnect the MAP sensor electrical connector.
  3. Turn ON the ignition, with the engine OFF.
    IMPORTANT: Certain resistances will not be detectable if a test lamp is not connected to provide a circuit load.
  4. Connect a test lamp between the MAP sensor 5-volt reference circuit and a good ground.
  5. Measure the voltage from the 5-volt reference circuit of the MAP sensor to a good ground, with a DMM, at the MAP sensor connector. Refer to Circuit Testing .
Is the voltage more than the specified value?		 4.8 V Go to Step 6  Go to Step 7 
6
  1. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the MAP sensor and the signal circuit of the MAP sensor.
  2. Observe the MAP sensor parameter with the scan tool.
Is the voltage more than the specified value?		 4.9 V Go to Step 9  Go to Step 8 
7 Test the 5-volt reference circuit between the engine control module (ECM) and the MAP sensor for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 10 
8 Test the MAP sensor signal circuit between the ECM and the MAP sensor for the following:
  • A short to ground
  • An open
  • High resistance

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 10 
9 Test for an intermittent and for a poor connection at the MAP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 11 
10 Test for an intermittent and for a poor connection at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 12 
11 Replace the MAP sensor. Refer to Manifold Absolute Pressure (MAP) Sensor Replacement .
Did you complete the replacement?		 - Go to Step 13  -
12 Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 13  -
13
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 14 
14 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals