Electronic Brake Control Module Scan Tool Information
Electronic Brake Control Module Scan Tool Data Parameters
| Parameter | System State | Expected Value | Description |
|---|---|---|---|
| Operating Conditions: Ignition ON | |||
| ABS Active | - | No | The scan tool displays Yes or No. Yes is displayed if the antilock brake system (ABS) is active. |
| Brake Pressure Sensor | - | Varies | This displays psi (kPa). This is the pressure at the brake pressure sensor measured in pounds per square inch (kilopascals). |
| Brake Pressure Sensor Input | - | Varies | This displays Volts. This is the input voltage of the brake pressure sensor. |
| Brake Temp Status | - | Normal | The scan tool displays Normal or Overtemp. This is the state of the brake temperature. |
| DRP Active | - | No | The scan tool displays Yes or No. Yes is displayed if the dynamic rear proportioning (DRP) is active. |
| DRP Disabled | - | No | The scan tool displays Yes or No. This is the state of the dynamic rear proportioning (DRP). |
| Ignition Voltage Signal | - | Varies | This displays Volts. This is the current ignition voltage signal. |
| Lateral Accelerometer Signal | - | Varies | This displays Volts. This is the state of the lateral accelerometer signal measured in Volts. |
| Lateral Accelerometer Signal | - | Varies | This displays g. This is the state of the lateral accelerometer signal measured in g. |
| Left TCS Isolation Solenoid Command | - | Off | The scan tool displays On or Off. This is the commanded state of the driver traction control system (TCS) isolation solenoid. |
| Left TCS Prime Solenoid Command | - | Off | The scan tool displays On or Off. This is the commanded state of the driver traction control system (TCS) prime solenoid. |
| LF Inlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the driver front inlet solenoid command. |
| LF Outlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the driver front outlet solenoid command. |
| LF Wheel Speed Sensor | - | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed at the driver front wheel speed sensor. |
| LR Inlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the driver rear inlet solenoid command. |
| LR Outlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the driver rear outlet solenoid command. |
| LR Wheel Speed Sensor | - | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed at the driver rear wheel speed sensor. |
| Pump Motor Relay Command | - | Off | The scan tool displays On or Off. This is the commanded state of the pump motor relay. |
| Pump Motor Relay Feedback Signal | - | Off | The scan tool displays On or Off. This is the state of the pump motor relay feedback signal. |
| RF Inlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the passenger front inlet solenoid command. |
| RF Outlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the passenger front outlet solenoid command. |
| RF Wheel Speed Sensor | - | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed at the passenger front wheel speed sensor. |
| Right TCS Isolation Solenoid Command | - | Off | The scan tool displays On or Off. This is the commanded state of the passenger traction control system (TCS) isolation solenoid. |
| Right TCS Prime Solenoid Command | - | Off | The scan tool displays On or Off. This is the commanded state of the passenger traction control system (TCS) prime solenoid. |
| Rough Road Detected | - | Varies | This displays g. |
| RR Inlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the passenger rear inlet solenoid command. |
| RR Outlet Solenoid Command | - | Off | The scan tool displays On or Off. This is the state of the passenger rear outlet solenoid command. |
| RR Wheel Speed Sensor | - | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed at the passenger rear wheel speed sensor. |
| Solenoid Relay Command | - | Varies | The scan tool displays On or Off. This is the commanded state of the solenoid relay. |
| Solenoid Relay Feedback Signal | - | Varies | The scan tool displays On or Off. This is the state of the solenoid relay feedback signal. |
| Steering Position Sensor | - | Varies | This displays °. This is the current steering wheel position measured in degrees. |
| Steering Sensor Is Centered | - | Yes | The scan tool displays Yes or No. Yes is displayed if the steering sensor is centered. |
| Steering Wheel Position | - | Varies | This displays °. This is the current steering wheel position measured in degrees. |
| Switched Battery Voltage Signal | - | Varies | This displays Volts. This is the switched battery voltage signal. |
| SWPS Signal A | - | Varies | This displays Volts. This is the current steering wheel position sensor (SWPS) A signal. |
| SWPS Signal B | - | Varies | This displays Volts. This is the current steering wheel position sensor (SWPS) B signal. |
| TCS Active | - | No | The scan tool displays Yes or No. Yes is displayed if the traction control system (TCS) is active. |
| TCS Enable | - | Varies | The scan tool displays Yes or No. Yes is displayed if the traction control system (TCS) is enabled. |
| Torque Request Signal | - | Varies | This displays %. This is the requested torque signal measured in percentage. |
| Torque Delivered Signal | - | Varies | This displays %. This is the delivered torque signal measured in percentage. |
| Vehicle Speed | - | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed. |
| VSES Active | - | No | The scan tool displays Yes or No. Yes is displayed if the vehicle stability enhancement system (VSES) is active. |
| VSES Enabled | - | Varies | The scan tool displays Yes or No. Yes is displayed if the vehicle stability enhancement system (VSES) is enabled. |
| Yaw Rate Sensor | - | 0 °/sec | This displays °/sec. This is the state of the yaw rate sensor measured in degrees per second. |
| Yaw Rate Signal | - | Varies | This displays Volts. This is the current yaw rate signal. |
Electronic Brake Control Module Scan Tool Output Controls
| Output Control | Description |
|---|---|
| Automated Bleed | This output control is used to bleed the ABS hydraulics. Refer to Antilock Brake System Automated Bleed Procedure . |
| LF Inlet Valve Solenoid | This output control is used to command the driver front inlet valve solenoid ON and OFF. |
| LF Outlet Valve Solenoid | This output control is used to command the driver front outlet valve solenoid ON and OFF. |
| LR Inlet Valve Solenoid | This output control is used to command the driver rear inlet valve solenoid ON and OFF. |
| LR Outlet Valve Solenoid | This output control is used to command the driver rear outlet valve solenoid ON and OFF. |
| RF Inlet Valve Solenoid | This output control is used to command the passenger front inlet valve solenoid ON and OFF. |
| RF Outlet Valve Solenoid | This output control is used to command the passenger front outlet valve solenoid ON and OFF. |
| RR Inlet Valve Solenoid | This output control is used to command the passenger rear inlet valve solenoid ON and OFF. |
| RR Outlet Valve Solenoid | This output control is used to command the passenger rear outlet valve solenoid ON and OFF. |