LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2007 >> Impala SS >> Repair and Diagnosis >> External Pages >> Different car >> Section 128 (Antilock Brake System With Traction Control System & Stability Control System) >> Diagnostic Information and Procedures >> DTC C0131 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Buick LaCrosse and 2006 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step tests for specified voltage on the brake pressure signal circuit.
  2. 3:  This step checks to see if voltage was below specified voltage.
  3. 4:  This step checks to see if voltage was below specified voltage.
  4. 5:  This step checks to see if voltage was above specified voltage of the 5-volt reference.
  5. 6:  This step tests for a short to ground in the 5-volt reference circuit.
  6. 7:  This step tests for a short to voltage in the 5-volt reference circuit.
  7. 8:  This step tests for a short to ground, a high resistance or an open in the 5-volt reference circuit.
  8. 9:  This step tests for a short to voltage, a high resistance or an open in the brake pressure sensor signal circuit.
  9. 10:  This step tests for a high resistance or an open in the ground circuit of the brake pressure sensor.
  10. 11:  This step checks the brake pressure sensor connector for poor connections.
  11. 12:  This step checks the EBCM connector for poor connections.
DTC C0131

Step Action Value(s) Yes No
Schematic Reference: ABS Schematics 
Connector End View Reference: ABS Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Turn OFF the ignition.
  2. Disconnect the electronic brake control module (EBCM).
  3. Install the J 39700  Universal Pinout Box with the J 39700-530  Cable Adapter between the EBCM and the EBCM harness connector. See Special Tools .
  4. Turn ON the ignition, with the engine OFF.
  5. Using the DMM, measure the voltage between pin 17 and pin 15 of the J 39700  . See Special Tools .
Is the voltage within the specified value?		 0.25-4.75 V Go to Diagnostic Aids Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the brake pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Using the DMM, measure the voltage between pin 17 and pin 15 of the J 39700  . See Special Tools .
Is the voltage greater than the specified value?		 5 V Go to Step 9  Go to Step 4 
4 
  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the signal circuit of the brake pressure sensor and the 5-volt reference circuit of the brake pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Using the DMM, measure the voltage between pin 17 and pin 15 of the J 39700  . See Special Tools .
Is the voltage less than the specified value?		 0.25 V Go to Step 8  Go to Step 5 
5 
  1. Turn OFF the ignition.
  2. Disconnect the fused jumper wire.
  3. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the brake pressure sensor and the signal circuit of the brake pressure sensor.
  4. Measure the voltage between the 5-volt reference circuit of the brake pressure sensor and the signal circuit of the brake pressure sensor.
Is the voltage measured greater than the specified value?		 5 V Go to Step 7  Go to Step 6 
6  Test the 5-volt reference circuit of the brake pressure sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
7  Test the 5-volt reference circuit of the brake pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 11 
8  Test the signal circuit of the brake pressure sensor for a short to ground, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
9  Test the signal circuit of the brake pressure sensor for a short to voltage, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 10 
10  Test the ground circuit of the brake pressure sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
11  Inspect for poor connections at the harness connector of the brake pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 13 
12  Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 14 
13 Replace the brake pressure sensor. Refer to Brake Fluid Pressure Sensor Replacement .
Did you complete the replacement?		 - Go to Step 15  -
14 Replace the EBCM. Refer to Control Module References for replacement, setup and programming.
Did you complete the replacement?		 - Go to Step 15  -
15
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About LEMON Manuals