Scan Tool Data List (w/Throttle Actuator Control)
The Engine Scan Tool Data List contains all engine related parameters that are available on the scan tool. The list is arranged in alphabetical order. A parameter may appear in any one of the data lists, and in some cases may appear more than once, or in more than one data list in order to group certain related parameters together.
Use the Engine Scan Tool Data List only after the following conditions are determined:
- The Diagnostic System Check - Engine Controls is completed.
- There are no diagnostic trouble codes (DTCs).
- The on-board diagnostics are functioning correctly.
Scan tool values from an engine that is operating correctly may be used for comparison with the engine you are diagnosing. The Engine Scan Tool Data List represents the values that would be seen on a normal operating engine.
Only the parameters listed below are referenced in this service information for use in diagnosis. If all values are within the typical range described below, refer to Symptoms - Engine Controls for diagnosis.
The column labeled Data List indicates where a parameter is located on the scan tool. Review the scan tool operating manual for the exact locations of the data lists. The following is a description of each term listed:
- All
-
The Parameter is in all data lists indicated below.
- Eng 1
-
Engine Data 1
- Eng 2
-
Engine Data 2
- Eng 3
-
Engine Data 3
- HO2S
-
HO2S Data
| Scan Tool Parameter | Data List | Parameter Range/Units | Typical Data Values |
|---|---|---|---|
| Engine Idling/Radiator Hose Hot/Park or Neutral/Closed Loop/Accessories Off | |||
| A/C High Side Pressure Sensor | Eng 2 | 0-5 Volts | Varies |
| A/C High Side Pressure Sensor | Eng 2, 3 | kPa/psi | Varies |
| A/C Relay Command | Eng 3 | On/Off | Off |
| A/C Request | Eng 3 | Yes/No | No |
| APP Sensor 1 and 2 | Eng 2 | 0-5 Volts | 0.5-4.5 Volts |
| BARO | Eng 2 | 65-104 kPa | Varies with altitude |
| Battery Voltage | Eng 2, 3, HO2S | 6-24 Volts | 12-15 Volts |
| Cruise Control ON/OFF Switch | Eng 2 | ON/OFF | OFF |
| Cruise Control Set/Coast Switch | Eng 2 | ON/OFF | OFF |
| Cruise Control Resume/Accel Switch | Eng 2 | ON/OFF | OFF |
| Cruise Control | Eng 2 | ON/OFF | OFF |
| Desired Idle Speed | Eng 2 | 0-8,000 RPM | 800 RPM |
| DTC Set This Ignition | Eng 1 | Yes/No | No |
| ECT Sensor | ALL | -40 to +130°C (-40 to +266°F) | Varies |
| ECT Sensor | Eng 2 | 0-5 Volts | Varies |
| EC Ignition Relay Command | Eng 3 | On/Off | On |
| EGR Position Sensor | Eng 2 | 0-5 Volts | 0.6-0.75 Volts |
| EGR Solenoid Command | Eng 2, 3 | 0-100% | 0% |
| Engine Load | Eng 1 | 0-99% | 20-30% - Idle 10-20% - 2500 RPM |
| Engine Run Time | HO2S | HH:MM:SS | Varies |
| Engine Speed | ALL | 0-8,000 RPM | 750-825 RPM |
| EVAP Purge Solenoid Command (If Equipped) | Eng 2, 3 | 0-100% | Varies |
| Fan High | Eng 3 | On/Off | Varies |
| Fan Low | Eng 3 | On/Off | Varies |
| Fuel Gage Control | Eng 3 | 0-100% | Varies |
| Fuel Level Sensor | Eng 2, 3, H02S | 0-5 Volts | Varies |
| Fuel Level Sensor | Eng 2, H02S | 0-100% | Varies |
| Fuel Pump Relay Command | Eng 3 | On/Off | On |
| Fuel Tank Pressure Sensor | Eng 3 | 0-5 Volts | Varies |
| Fuel Tank Pressure Sensor | Eng 3 | mmHg/in H2O | Varies |
| HO2S Bank 1 and 2 Sensor 1 | Eng 1, H02S | 0-1,006 mV | Varies 400-800 mV |
| HO2S Bank 1 and 2 Sensor 2 | Eng 1, H02S | 0-1,006 mV | Varies 400-800 mV |
| HO2S Htr. Bn. 1 and 2 Sen. 1 Command | H02S | 0-100% | Varies |
| HO2S Htr. Bn. 1 and 2 Sen. 2 Command | H02S | 0-100% | Varies |
| IAT Sensor | ALL | -39 to +140°C (-38 to +284°F) | Varies |
| IAT Sensor | Eng 2 | 0-5 Volts | Varies |
| Idle Speed Motor Position Sensor | Eng 2 | 0-100% | Varies |
| IMT Valve Command | Eng 3 | On/Off | Off |
| IMT Valve Feedback Signal | Eng 3 | 0-5 Volts | Varies |
| Knock Sensor | Eng 2 | 0-5 Volts | Varies |
| Long Term FT Bank 1 and 2 | Eng 1 | -50 to +50% | 0% |
| Loop Status | Eng 1 | Open Loop/Closed Loop | Closed Loop |
| MAF Sensor | Eng 1, 2 | g/s | Varies |
| MAF Sensor | Eng 2 | 0-5 Volts | Varies |
| Main Relay Control | Eng 3 | ON/OFF | ON |
| MAP Sensor | All | kPa/PSI | 32-40 kPa Varies with Altitude |
| MAP Sensor | Eng 2 | 0-5 Volts | 1.15-1.3 Volts |
| MIL Command | Eng 1 | On/Off | Off |
| Short Term FT Average Bank 1 and 2 | H02S | -50 to +50% | -3 to +3% |
| Short Term FT Bank 1 and 2 | Eng 1, HO2S | -50 to +50% | -3 to +3% |
| Spark | Eng 1 | -20 to +40 Degrees | 2-10 Degrees |
| TP Sensor | Eng 2 | 0-5 Volts | 4.0-4.5 Volts |
| TP Sensor | ALL | Degrees | Varies |
| TP Sensor 1 and 2 | Eng 2 | 0-5 Volts | Varies |
| Transmission Gear Selector Signal | Eng 3, H02S | Park/Neutral/In Gear | Park/Neutral |
| Vehicle Security Status (If Equipped) | Eng 3 | Enabled/Disabled | Enabled |
| Vehicle Speed Sensor | ALL | km/h mph |
0 km/h (0 mph) |