LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2005 >> Venture Base, Van Cargo Extended >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - 3.4L DTC P0446 To P1640 >> DTC Tests >> DTC P0650 >> Test Description

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  This step tests for a short to ground in the MIL control circuit. With the PCM disconnected and the ignition ON, the MIL should be OFF.
  2. 6:  This step tests for a short to voltage on the MIL control circuit. With the fuse removed, there should be no voltage on the MIL control circuit.
DTC P0650

Step Action Values Yes No
Schematic Reference: Instrument Cluster Schematics in Instrument Panel, Gages, and Console or Engine Controls Schematics
Connector End View Reference: Instrument Panel, Gages, and Console Component Views , Instrument Panel, Gages, and Console Connector End Views in Instrument Panel, Gages, and Console or Powertrain Control Module (PCM) Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Command the malfunction indicator lamp (MIL) ON and OFF with a scan tool.
Does the MIL turn ON and OFF when commanded with a scan tool?		 - Go to Step 3  Go to Step 4 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Does the DTC fail this ignition?		 - Go to Step 4  Go to Intermittent Conditions
4 Inspect the that supplies voltage to the MIL.
Is the fuse open?		 - Go to Step 12  Go to Step 5 
5 
  1. Turn OFF the ignition.
  2. Disconnect the powertrain control module (PCM).
  3. Turn ON the ignition.
Is the MIL OFF?		 - Go to Step 6  Go to Step 13 
6 
  1. Turn OFF the ignition.
  2. Remove the fuse that supplies voltage to the MIL.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the voltage from the MIL control circuit to a good ground.
Is the voltage less than the specified value?		 1 V Go to Step 7  Go to Step 14 
7
  1. Turn OFF the ignition.
  2. Install the fuse that supplies voltage to the MIL.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a 3-amp fused jumper wire between the MIL control circuit of the PCM and a good ground.
Is the MIL illuminated?		 - Go to Step 11  Go to Step 8 
8
  1. Turn OFF the ignition.
  2. Remove the instrument panel cluster (IPC). Refer to Instrument Panel Cluster (IPC) Replacement in Instrument Panel, Gages, and Console.
  3. Probe the MIL battery positive voltage circuit of the IPC harness connector with a test lamp that is connected to a good ground.
Does the test lamp illuminate?		 - Go to Step 9  Go to Step 15 
9 Test the MIL control circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct a condition?		 - Go to Step 18  Go to Step 10 
10 Test for an intermittent and for a poor connection at the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 18  Go to Step 16 
11 Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Repairs.
Did you find and correct the condition?		 - Go to Step 18  Go to Step 17 
12 Repair the short to ground in the battery positive voltage circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 18  -
13 Repair the short to ground in the MIL control circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 18  -
14 Repair the short to voltage in the MIL control circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 18  -
15 Repair the open in the MIL battery positive voltage circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 18  -
16 Replace the IPC. Refer to Instrument Panel Cluster (IPC) Replacement in Instrument Panel, Gages, and Console.
Did you complete the replacement?		 - Go to Step 18  -
17 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 18  -
18
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 19 
19 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals