Engine Specifications

GENERAL SPECIFICATIONS

Application	Specification
Displacement	134 Cu. In. (2.2L)
Bore	3.50" (89 mm)
Stroke	3.46" (88 mm)
Compression Ratio	8.85:1
Fuel System	MFI

CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECIFICATIONS

Application		In. (mm)
Crankshaft End Play		.002-.007 (.05-.18)
Main Bearings
Journal Diameter		2.4945-2.4954 (63.360-63.384)
Journal Out-Of-Round		.00019 (.0048)
Journal Taper		.00019 (.0048)
Oil Clearance		.0006-.0019 (.015-.048)
Connecting Rod Bearings
Journal Diameter		1.9983-1.9994 (50.756-50.784)
Journal Out-Of-Round		.00019 (.0048)
Journal Taper		.00019 (.0048)
Oil Clearance		.00098-.0031 (.0249-.079)

CONNECTING RODS SPECIFICATIONS

Application

In. (mm)

Maximum Bend

⁽¹⁾

Maximum Twist

⁽¹⁾

Side Play

.0039-.0149 (.099-.378)

⁽¹⁾	Replace rod if any bend or twist exists.

PISTONS, PINS & RINGS SPECIFICATIONS

Application

In. (mm)

Pistons

Clearance

⁽¹⁾.00059-.00185 (.0150-.0470)

Diameter

⁽²⁾

Pins

Diameter

.8000-8002 (20.320-20.325)

Piston Fit

2000

.00031-.00061 (.0079-.0155)

2001

.00031-.00071 (.0079-.0180)

Rod Fit

2000

.0013-0025 (.033-.064)

2001

.0008-.0020 (.020-.051)

Rings

No. 1

End Gap

.010-.020 (.250-.510)

Side Clearance

.0020-.0035 (.051-.089)

No. 2

End Gap

.0012-.0177 (.030-.450)

Side Clearance

2000

.0016-.0031 (.041-.079)

2001

.0008-.0031 (.020-.079)

No. 3 (Oil)

End Gap

.010-.030 (.254-.762)

Side Clearance

.0005-.0087 (.013-.221)

⁽¹⁾	Measured 1.68" (42.7 mm) from top of piston.

⁽²⁾	Information is unavailible from manufacturer.

CYLINDER BLOCK SPECIFICATIONS

Application

In. (mm)

Cylinder Bore

Standard Diameter

3.5036-3.5043 (88.991-89.009)

Maximum Taper

.0005 (.013)

Maximum Out-Of-Round

.0005 (.013)

Maximum Deck Warpage

⁽¹⁾

⁽¹⁾	If more than .0100" (.250 mm) material must be removed from original surface of deck, replace cylinder block.

VALVES & VALVE SPRINGS SPECIFICATIONS

Application

Specification

Valves

Face Angle

45°

Head Diameter

Exhaust

1.45" (37 mm)

Intake

1.73" (44 mm)

Head Margin

Exhaust

.073-.083" (1.87-2.13 mm)

Intake

.048-.058" (1.23-1.49 mm)

Face Runout (Maximum)

.0014" (.036 mm)

Valve Springs

Free Length

1.910" (48.514 mm)

Out-Of-Square

⁽¹⁾

Lbs. @ In. (kg @ mm)

Valve Spring Pressure (Minimum)

Valve Closed

2000

72.8-81.2 @ 1.600 (33.02-36.83 @ 40.6)

2001

73.1-81.2 @ 1.600 (33.15-36.83 @ 40.6)

Valve Open

201-215 @ 1.175 (91.17-97.52 @ 29.9)

⁽¹⁾	Information is unavailible from manufacturer.

CYLINDER HEAD SPECIFICATIONS

Application

Specification

Maximum Warpage

⁽¹⁾ .004" (.10 mm)

Valve Seats

Intake Valve

Seat Angle

45 degrees

Seat Width

.110" (2.79 mm)

Seat Runout (Maximum)

⁽²⁾

Exhaust Valve

Seat Angle

45 degrees

Seat Width

.138" (3.51 mm)

Seat Runout (Maximum)

⁽²⁾

Valve Guides

Intake Valve Stem-To-Guide Oil Clearance

.0007-.0020" (.018-.051 mm)

Exhaust Valve Stem-To-Guide Oil Clearance

.0014-.0029" (.036-.074 mm)

⁽¹⁾	If more than .010" (.25 mm) material must be removed from original surface of cylinder head, replace cylinder head.

⁽²⁾	Not provided by manufacturer.

CAMSHAFT SPECIFICATIONS

Application		In. (mm)
Journal Diameter		1.868-1.869 (47.45-47.47)
Lobe Lift (Intake and Exhaust)
2000		.2630 (6.680)
2001		.2633 (6.687)
Oil Clearance
2000		.0005-.0035 (.013-.089)
2001		.0015-.0035 (.038-.089)