Removal Procedure

Raise and support the vehicle. Lifting and Jacking the Vehicle
Courtesy of GENERAL MOTORS COMPANY

Front Wheelhouse Liner Bolt - Left Side (1) - Remove [4x]
Front Tire Front Air Deflector Bolt - Left Side (2) - Remove
Front Bumper Fascia Bolt - Left Side (3) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Reposition the left front wheelhouse liner (1) to gain access to the left side upper front bumper fascia bolt (2).
Remove the left side upper front bumper fascia bolt (2).
Courtesy of GENERAL MOTORS COMPANY

Front Wheelhouse Liner Bolt - Right Side (1) - Remove [4x]
Front Tire Front Air Deflector Bolt - Right Side (2) - Remove
Front Bumper Fascia Bolt - Right Side (3) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Reposition the right front wheelhouse liner (1) to gain access to the right side upper front bumper fascia bolt (2).
Remove the right side upper front bumper fascia bolt (2).
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Air Deflector Screw (1) - Remove [10x]
Remove the support and lower the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Bolt (1) - Remove [6x]
Courtesy of GENERAL MOTORS COMPANY

On the right side of the front bumper fascia carefully push a small nylon wedge between the front bumper fascia (1), the front bumper fascia guide (2), and the front headlamp (3). Insert a suitable flat-bladed plastic trim tool into the fascia slot and depress the snaps one at a time and pull on the fascia at the same time to gradually remove the right side of the front bumper fascia.
Courtesy of GENERAL MOTORS COMPANY

Reposition the front bumper fascia on the right side to gain access to the electrical connector (1).
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

On the left side of the front bumper fascia carefully push a small nylon wedge between the front bumper fascia (1), the front bumper fascia guide (2), and the front headlamp (3). Insert a suitable flat-bladed plastic trim tool into the fascia slot and depress the snaps one at a time and pull on the fascia at the same time to gradually remove the left side of the front bumper fascia.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Duct Retainer (1) - Remove [3x]
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Duct Retainer (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
The front bumper fascia support brace (2) may have a forward range radar sensor attached, if equipped.

Front Bumper Fascia Support Brace Bolt (1) - Remove [3x]
Front Bumper Fascia Support Brace (2) - Remove
Disconnect the electrical connector from the forward range radar sensor, if equipped.
Courtesy of GENERAL MOTORS COMPANY

Intake Air Duct Retainer (1) - Remove [2x]
Radiator Air Lower Seal Retainer (2) - Remove [2x]
Radiator Air Lower Baffle Retainer (3) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Front End Sheet Metal Cross Brace Bolt (1) - Remove [4x]
Front End Sheet Metal Cross Brace (2) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Horn Bolt (1) - Remove [2x]
Horn (2) - Reposition [2x]
Courtesy of GENERAL MOTORS COMPANY

Reposition the wiring harness.
Front Bumper Impact Bar Bolt (1) - Remove [8x]
Front Bumper Impact Bar (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Front Duct (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Throttle Inlet Absolute Pressure Sensor Bolt (1) - Remove
Throttle Inlet Absolute Pressure Sensor (2) - Remove