LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2020 >> XT6 Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 35 (Automatic Level Control System) >> Diagnostic Information and Procedures >> DTC C1480 or C1485 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2020 GMC Yukon XL, 2020 GMC Yukon, 2020 Chevrolet Tahoe, 2020 Chevrolet Suburban, and 2020 Cadillac Escalade ESV. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF and all vehicle systems OFF. Disconnect the harness connector at the appropriate B152 Suspension Position Sensor. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the low reference circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the K38 Chassis Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K38 Chassis Control Module.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Test for 4.8 - 5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K38 Chassis Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K38 Chassis Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K38 Chassis Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K38 Chassis Control Module.
    • Go to next step: If within 4.8 - 5.2 V 
  5. Verify the appropriate scan tool Suspension Position Sensor parameter is less than 0.6 V
    • If 0.6 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K38 Chassis Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K38 Chassis Control Module
    • Go to next step: If less than 0.6 V 
  6. Install a 3 A fused jumper wire between the signal circuit terminal 3 and the 5 V reference circuit terminal 1.
  7. Verify the scan tool Suspension Position Sensor parameter is greater than 2.8 V.
    • If less than 2.8 V 
    1. Ignition OFF, disconnect the harness connector at the K38 Chassis Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K38 Chassis Control Module.
    • Go to next step: If greater than 2.8 V 
  8. Replace the B152 Suspension Position Sensor.
scientia non olet · About LEMON Manuals