Transfer Case - BW 4474
- Specifications
- Schematic Wiring Diagrams
- Component Locator
- Diagnostic Information and Procedures
- DTC C038C: Transfer Case Clutch Identifier Not Programmed
- DTC C0399: Transfer Case Clutch Control Circuit
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- DTC C0401: Transfer Case Fluid Temperature Sensor Circuit
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- DTC C0569: System Configuration
- DTC P0601-P0604 or P062F: Control Module
- DTC P0641: 5 V Reference 1 Circuit
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- Symptoms - Transfer Case
- No Correction for Slip in All-Wheel Drive Mode
- Service All-Wheel Drive Indicator Always On
- All-Wheel Drive Off Indicator Always On
- Transfer Case Popping Noise
- Transfer Case Whine or Rumble Noise
- Transfer Case Clunk During Acceleration and Deceleration
- Transfer Case Leak Diagnosis
- Repair Instructions - On Vehicle
- Transfer Case Fluid Replacement
- Drain Plug Replacement
- Fill Plug Replacement
- Transfer Case Fluid Temperature Sensor Replacement
- Transfer Case Control Module Replacement
- Transfer Case Assembly Replacement
- Input Shaft Seal Replacement
- Rear Output Shaft Seal Replacement
- Front Output Shaft Seal Replacement
- Oil Distribution Tube Replacement
- Transfer Case Vibration Dampener Replacement
- Repair Instructions - Off Vehicle
- Transfer Case Disassemble
- Vibration Dampener Removal
- Transfer Case Holding Fixture Installation
- Front Output Shaft and Seal Removal
- Oil Drain Plug, Oil Fill Plug, and Fluid Temperature Sensor Removal
- Oil Delivery Tube and Oil Pump Removal
- Rear Output Shaft Flange and Seal Removal
- Vent and Adapter Studs Removal
- Rear Case Half Removal
- Two/Four Wheel Drive Clutch Coil Removal
- Oil Baffle, Oil Pump Screen, and Case Half Locating Pin Removal
- Idler Gear Rear Bearing Race and Front Output Shaft Rear Bearing Removal
- Rear Output Shaft Rear Bearing Removal
- Two/Four Wheel Drive Clutch Coil Housing Removal
- Armature and Front Drive Axle Clutch Assembly Removal
- Input Gear and Thrust Bearing Removal
- Idler Gear, Front Output Shaft Gear, and Oil Baffle Removal
- Input Shaft Removal
- Input Bearing Removal
- Front Output Shaft Front Bearing and Idler Gear Front Bearing Race Removal
- Input Shaft Seal Removal
- Transfer Case Front Drive Axle Viscous Clutch Disassemble
- Transfer Case Cleaning and Inspection
- Transfer Case Front Drive Axle Viscous Clutch Assemble
- Transfer Case Assemble
- Front Output Shaft Front Bearing and Idler Gear Front Bearing Race Installation
- Input Shaft Seal Installation
- Input Bearing Installation
- Input Shaft Installation
- Idler Gear, Front Output Shaft Gear, and Oil Baffle Installation
- Input Gear and Input Shaft Thrust Bearing Installation
- Armature and Front Drive Axle Clutch Assembly Installation
- Oil Distribution Hub and Two/Four Wheel Drive Clutch Coil Housing Installation
- Rear Output Shaft Rear Bearing Installation
- Idler Gear Rear Bearing Race and Front Output Shaft Rear Bearing Installation
- Oil Baffle, Oil Pump Screen, and Case Half Locating Pin Installation
- Two/Four Wheel Drive Clutch Coil Installation
- Oil Distribution Hub Installation
- Rear Case Half Installation
- Vent and Adapter Studs Installation
- Rear Output Shaft Seal Installation
- Rear Output Shaft Flange Installation
- Oil Delivery Tube and Oil Pump Installation
- Oil Fill Plug, Drain Plug, and Fluid Temperature Sensor Installation
- Front Output Shaft Seal Installation
- Front Output Shaft Installation
- Transfer Case Holding Fixture Removal
- Vibration Dampener Installation
- Four Wheel Drive Clutch Shim Selection
- Transfer Case Disassemble
- Description and Operation
- Special Tools and Equipment