LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2017 >> CT6 Plug-In >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Headlights >> Lighting System - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> DTC B3415: Headlamp Leveling Control Module Axle Sensor Supply Circuit >> Circuit/System Testing

Circuit/System Testing

  1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the appropriate B152L Suspension Position Sensor, ignition ON/vehicle in Service Mode.
  2. Verify a test lamp illuminates between the low reference circuit terminal 2 and B+.
    • If the test lamp does not illuminate 
    1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If the test lamp illuminates 
  3. Ignition ON/vehicle in Service Mode.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • If between 4.8-5.2 V 
  5. Verify the appropriate scan tool Leveling Position Sensor Signal parameter is less than 5%.
    • If 5% or greater 
    1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • If less than 5% 
  6. Install a 3 A fused jumper wire between the 5 V reference circuit terminal 1 and the signal circuit terminal 3.
  7. Engine RUNNING/vehicle ON, verify the appropriate scan tool Leveling Position Sensor Signal parameter is greater than 90%.
    • If less than 90% 
    1. Ignition OFF/Vehicle OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If 90% or greater 
  8. Test or replace the B152L Suspension Position Sensor.
scientia non olet · About LEMON Manuals