Specifications Index
CTS
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 158 ft lbs (215 N.m) | ||
| Rear | 158 ft lbs (215 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Belt Routing | See illustrations under WATER PUMP AND GENERATOR BELT REPLACEMENT or AIR CONDITIONING COMPRESSOR AND POWER STEERING PUMP BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LY7, LLT) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LY7, LLT) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 PSI (138 kPa) |
||
| Overhaul | See ENGINE MECHANICAL SPECIFICATIONS 3.6L (LY7) or ENGINE MECHANICAL SPECIFICATIONS 3.6L (LLT) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | Step 1 22 ft lbs (30 N.m) Final Step + an additional 45 degrees |
||
| Fuel System | |||
| Pressure Specification | 55-60 psi (380-410 kPa) | ||
| Fuel Pressure Test Procedure | See Fuel Pressure Gage Installation and Removal (LP1, LY7) and FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | The fuel filter is located in the primary fuel tank module | ||
| Fuel Filter R & I | FUEL FILTER REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | |||
| 3.6L | Coil on plug | ||
| Spark Plug | |||
| 3.6L (Type AC 41-990) | |||
| Gap | 0.044 in (1.10 mm) | ||
| Torque | 15 lb ft (20 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft lbs (140 N.m) | ||