LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2006 >> Escalade EXT >> Repair and Diagnosis >> External Pages >> Different car >> Section 1704 (Fixed And MOVEABLE Windows System) >> Repair Instructions >> Rear Sliding Window Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Rear Side Window Catch Screws, Gasket, Nuts & Frame
    GM1851983Courtesy of GENERAL MOTORS CORP.
  1. Install the rear sliding window (4) to the frame.
  2. Align the window to the upper and lower frame, push down the window and then pull upward locking the window in the frame.
  3. Slide the window all the way to the right (passenger side).
    4. CAUTION: Refer to Fastener Caution .
  4. Install the rear sliding window catch screws (1), catch, gasket (2) and nuts (3).

    Tighten:  Tighten the nuts to 3 N.m (27 lb in).

    5. Fig 2: View Of Regulator & Cables
    GM1852007Courtesy of GENERAL MOTORS CORP.
  5. Slide window by hand, back and forth in the window frame to ensure proper operation before installing the regulator to the motor.
  6. Install the window to the halfway position.
  7. Install the regulator (1) and cables (2) to vehicle.
    8. Fig 3: View Of Cable Ends At Window Guide
    GM1851995Courtesy of GENERAL MOTORS CORP.
  8. Install the cable ends (1) to the window guide (2) at each end of the window.
    9. Fig 4: View Of Regulator & Screw
    GM1852031Courtesy of GENERAL MOTORS CORP.
    NOTE: When installing the regulator (2) align the gear to the motor drivegear before installing the screw.
  9. Install the regulator (2) to the motor/module.
  10. Install the screw (1) to the motor/module.

    Tighten:  Tighten nuts to 5 N.m (44 lb in).

    11. Fig 5: View Of Pulley, Tabs & Frame
    GM1862458Courtesy of GENERAL MOTORS CORP.
  11. Install the rear sliding window pulley (1).
    1. Align the tabs (2) on the pulley (1) with the notch in the frame (3).
    2. Turn the pulley downward, locking the pulley into the frame (3).
    12. Fig 6: View Of Regulator Cables & Retainers
    GM1851990Courtesy of GENERAL MOTORS CORP.
  12. Install the regulator cables (2) to the retainers (1) across the bottom edge of the window frame.
    13. Fig 7: View Of Rear Window Pulley, Tabs & Cover
    GM1862459Courtesy of GENERAL MOTORS CORP.
  13. Install the rear sliding window pulley covers (2) to the pulley (3), clip the tabs (1) in place.
    14. Fig 8: View Of Rear Sliding Window Stops
    GM1851984Courtesy of GENERAL MOTORS CORP.
  14. Install the rear sliding window stops (1) until fully seated.
  15. Cycle the rear sliding window to the fully closed position.
  16. Install the lower garnish molding. Refer to Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48) or Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48) or Rear Window Lower Garnish Molding Replacement (Regular Cab) .
  17. Inspect the rear sliding window for proper operation.
  18. Clean the window.
scientia non olet · About LEMON Manuals