LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2021 >> Envision Preferred, AWD >> Repair and Diagnosis (Single Page) >> Body & Frame >> Body, Cab Control Systems >> Vehicle Access System >> Diagnostic Information and Procedures >> DTC B10CB or B10CC >> Circuit/System Testing

Circuit/System Testing

Test 1

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A24D Front Side Door Outside Handle - Left
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 5 & Ground
    • If 10 ohms or greater 
    1. Disconnect the ground connection: G325
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 5 @ Component harness & Terminal G325
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On/Vehicle - In Service Mode
  5. Verify the scan tool parameter: Left Front Door Exterior Lock/Unlock Switch Status = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K9 Body Control Module
    3. Test for infinite resistance between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 1 & Ground circuit terminal 5
  7. Verify the scan tool parameter: Left Front Door Exterior Lock/Unlock Switch Status = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: K9 Body Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 1 @ Component harness & Terminal 28 X6 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  8. Test or replace the component: A24D Front Side Door Outside Handle - Left

Test 2

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A24P Front Side Door Outside Handle - Right
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 5 & Ground
    • If 10 ohms or greater 
    1. Disconnect the ground connection: G328
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 5 @ Component harness & Terminal G328
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On/Vehicle - In Service Mode
  5. Verify the scan tool parameter: Right Front Door Exterior Lock/Unlock Switch Status = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K9 Body Control Module
    3. Test for infinite resistance between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 1 & Ground circuit terminal 5
  7. Verify the scan tool parameter: Right Front Door Exterior Lock/Unlock Switch Status = Active
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: K9 Body Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 1 @ Component harness & Terminal 28 X8 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  8. Test or replace the component: A24P Front Side Door Outside Handle - Right
scientia non olet · About LEMON Manuals