Common Specs & Procedures Index
ENVISION COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities |
||
| Torque | Fastener Specifications | ||
| Front Wheel Drive Shaft Nut | |||
| Tighten | First Pass: 285 N.m (210 lb. ft.) Second Pass: Release/Loosen 360 degrees Final Pass 250 N.m (185 lb ft) |
||
| Rear Wheel Drive Shaft Nut | |||
| Tighten | First Pass: 150 N.m (111 lb. ft.) Second Pass Release/Loosen 45 degrees Final Pass: 250 N.m (185 lb ft) |
||
| Battery | Battery Inspection/Test , or Battery Electrical Drain/Parasitic Load Test | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT FRONT, LEFT REAR, RIGHT FRONT Hydraulic Brake System Bleeding (Manual) Hydraulic Brake System Bleeding (Pressure) |
||
| Disc Brakes | |||
| Service Specifications | Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | NA | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the figure under Drive Belt Replacement (LCV) or Drive Belt Replacement (LTG) |
||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 2.0L/2.5L | Engine Coolant Thermostat Housing Replacement | ||
| Water Pump R & I | |||
| 2.0L/2.5L | Water Pump Replacement | ||
| Engine Mechanical | |||
| Compression | Engine Compression Test | ||
| Oil Pressure | LCV Minimum - @700 RPM @100°C - 154 - 220 kPa (22-32 psi) LTG Minimum - @700 RPM @100°C - 140-200 kPa (20-29 psi) |
||
| Overhaul | LCV Engine Mechanical Specifications (LCV) LTG Engine Mechanical Specifications (LTG) |
||
| Torque | LCV Fastener Specifications (LCV) LTG Fastener Specifications (LTG) |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque - 2.0L (LTG) | Flywheel First Pass - 30 N.m (22 lb ft) Final Pass - additional 80 degrees Flexplate First Pass - 20 N.m (15 lb ft) Second Pass - 30 N.m (22 lb ft) Final Pass - additional 40 degrees |
||
| Flywheel/Flex Plate/Drive Plate Torque - 2.5L (LCV) | Flexplate First Pass - 30 N.m (22 lb ft) Final Pass - additional 40 degrees |
||
| Fuel System | |||
| 2.0L/2.5L | |||
| Pressure Specification | Ignition ON, Engine OFF - 345-650 kPa (50-94 psi) | ||
| Fuel Pressure Test Procedure | Circuit/System Description | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | Fuel Pump Power Control Module Replacement | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| See Parts Catalog for Application | |||
| Gap | 0.95-1.10 mm (0.037-0.043 in) | ||
| Torque | 20 N.m (15 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Nut Torque | 190 N.m (140 lb ft) For Tightening Sequence, Please see the Figure Under Installation Procedure |
||