Common Specs & Procedures Index
Cascada
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Automatic - Fastener Specifications |
||
| Front Wheel Drive Shaft Nut | |||
|
150 Nm (111 lb ft) | ||
|
Loosen by 45 Degrees | ||
| Final Pass | 250 Nm (184 lb ft) | ||
| Rear Wheel Bearing / Hub Assembly Mounting Bolts | |||
|
50 N.m (37 lb ft) | ||
| Final Pass | 30 to 45 Degrees | ||
| Battery | Battery Description and Operation | ||
| Brakes | |||
| Bleeding Sequence | Hydraulic Brake System Bleeding | ||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Generator Replacement | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See graphic at "Drive Belt Routing" under: Installation Procedure | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 1.6L | Engine Coolant Thermostat Replacement | ||
| Water Pump R & I | |||
| 1.6L | Water Pump Replacement | ||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | Compression Ratio: 9.5:1 Engine Compression Test |
||
| Oil Pressure | At idle oil pressure must be greater than 150 kPa (21.76 psi) with oil temperature 85°C (185°F) or more. | ||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Automatic Transmission Flex Plate Bolt | |||
|
30N.m (22 lb ft) | ||
|
70 degrees | ||
| Fuel System | |||
| Pressure Specification | High Pressure Fuel Pump: 2 to 15 MPa (290 to 2176 psi) Injection Pressure of Fuel Rail System: 200 bar Nominal Pressure: 200 bar |
||
| Fuel Pressure Test Procedure | Circuit/System Verification | ||
| Fuel Filter Location | Inside the Fuel Tank: Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | Fuel Tank Fuel Pump Module Replacement | ||
| Ignition | |||
| Firing Order Cylinder Identification |
1-3-4-2 See graphic for 4 cylinder engine at: FIRING ORDER & CYLINDER IDENTIFICATION |
||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug - For application, see parts catalog. | |||
| 1.6L | |||
| Gap - All (Except LKN) | 0.60 mm-0.70 mm (0.024 in-0.028 in) | ||
| Gap - LKN | 0.65 mm-0.75 mm (0.026 in-0.030 in) | ||
| Torque | 17 N.m (13 lb. ft.) | ||
| Starting | |||
| Starter | Starter Replacement | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) See the graphic at "Wheel Nut Tightening Sequence" under: Installation Procedure |
||