LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2016 >> Envision >> Repair and Diagnosis >> Body & Frame >> Windows >> Fixed And MOVEABLE Window System >> Diagnostic Information and Procedures >> Power Windows Malfunction >> Circuit/System Testing

Circuit/System Testing

Driver Window Motor Malfunction

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the M74D Window Motor-Driver. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 2 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the M74D Window Motor-Driver.
    • If the test lamp illuminates 
  5. Test or replace the M74D Window Motor-Driver.

Driver Window Switch Malfunction

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the S79D Window Switch-Driver. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 4 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S79D Window Switch-Driver.
    • If the test lamp illuminates 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 3 and the ground circuit terminal 1.
    6. NOTE:

    Leaving the 3 A fused jumper wire connected between the signal circuit and ground for greater than 60 sec will cause the scan tool Driver Window Main Control Down Switch parameter to change from Active to Inactive

  6. Verify the scan tool Driver Window Main Control Down Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, Ignition ON.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 3 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 1 V between the S79D Window Switch-Driver signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  7. Install a 3 A fused jumper wire between the signal circuit terminal 6 and the ground circuit terminal 1.
    8. NOTE:

    Leaving the 3 A fused jumper wire connected between the signal circuit and ground for greater than 60 sec will cause the scan tool Driver Window Main Control Up Switch parameter to change from Active to Inactive

  8. Verify the scan tool Driver Window Main Control Up Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, Ignition ON.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 6 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 1 V between the S79D Window Switch-Driver signal circuit 6 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  9. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the ground circuit terminal 1.
    10. NOTE:

    Leaving the 3 A fused jumper wire connected between the signal circuit and ground for greater than 60 sec will cause the scan tool Driver Window Main Control Express Switch parameter to change from Active to Inactive

  10. Verify the scan tool Driver Window Main Control Express Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, Ignition ON.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 1 V between the S79D Window Switch-Driver signal circuit 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  11. Test or replace the S79D Window Switch-Driver.

Passenger Power Window Inoperative

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the appropriate passenger or rear S79 Window Switch. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal listed below and ground:
    • S79P Window Switch-Passenger - ground circuit terminal 1
    • S79LR Window Switch-Left Rear - ground circuit terminal 5
    • S79RR Window Switch-Right Rear - ground circuit terminal 5
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal listed below and ground:
    • S79P Window Switch-Passenger - B+ circuit terminal 4
    • S79LR Window Switch-Left Rear - B+ circuit terminal 8
    • S79RR Window Switch-Right Rear - B+ circuit terminal 8
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S79 Window Switch
    • If the test lamp illuminates 
  5. Ignition OFF, connect the harness connector at the S79 Window Switch and disconnect the harness connector at the M74 Window Motor.
  6. Test for less than 5 Ω between the control circuit terminal 1 and ground.
    • If 5 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the S79 Window Switch.
    2. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the S79 Window Switch.
    • If less than 5 Ω 
  7. Test for less than 5 Ω between the control circuit terminal 2 and ground.
    • If 5 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the S79 Window Switch.
    2. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the S79 Window Switch.
    • If less than 5 Ω 
  8. Connect a test lamp between control circuit terminal 1 and control circuit terminal 2, ignition ON.
  9. Verify the test lamp turns ON when commanding the UP and DOWN states with the S79 Window Switch.
    • If the test lamp remains OFF during either of the commands 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the S79 Window Switch.
    2. Test for infinite resistance between each control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S79 Window Switch.
    • If the test lamp turns ON during each of the commands 
  10. Test or replace the M74 Window Motor.
scientia non olet · About LEMON Manuals