Common Specs & Procedures Index
Cascada
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | Automatic - FASTENER SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
|
150 N.m (111 lb ft) | ||
|
Loosen by 45 Degrees | ||
| Final Pass | 250 N.m (184 lb ft) | ||
| Battery | N/A | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under INSTALLATION PROCEDURE | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 1.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 1.6L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | Maximum pressure differential 100 kPa (14.5 psi) ENGINE COMPRESSION TEST |
||
| Oil Pressure | At idle oil pressure must be greater than 150 kPa (21.76 psi) with oil temperature 85°C (185°F) or more. | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Automatic Transmission Flex Plate Bolt | 60 N.m (44 lb. ft.) | ||
| Fuel System | |||
| Pressure Specification | Ignition ON, Engine OFF - 345-650 kPa (50-94 psi) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug - For application, see parts catalog. | |||
| 1.6L | |||
| Gap - All (Except LKN) | 0.60 mm-0.70 mm (0.024 in-0.028 in) | ||
| Gap - LKN | 0.65 mm-0.75 mm (0.026 in-0.030 in) | ||
| Torque | 18 N.m (13 lb. ft.) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) For Lug Nut Tightening Sequence, Please See the Figure Under INSTALLATION PROCEDURE |
||